Stepper Motor Drivers

This 3D Printer MKS OSC Stepper Motor Controller Pulse PWM Speed Reversing Module is a pulse generating module, which used as a  signal for stepper drivers. To control the stepper motor,

1. Compatible 3D Printer: MKS Robin
2. Operating Voltage: 3.3V
3. Size: 25 * 23mm
4. Language: EN / CN (auto-ID)

1. Supply Voltage : 8-35 VDC.
2. Current : 1.0A  (no heatsink ).
3. Current : 2.0A (with heat-sinking).
4. logic input : 3 – 5.5V .
5. Automatic current decay mode detection / choice.
6. Mixed with slow current decay mode.

1. Compact size, easy to install and use.
2. All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
3. Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
4. E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.

1. 2-phase stepper motors up to 2.8A coil current (peak), 2A RMS
2. STEP/DIR Interface with 8, 16, 32 or 64 microstep pin setting
3. Smooth Running 256 microsteps by MicroPlyer interpolation
4. StealthChop2 silent motor operation
5. Spread Cycle highly dynamic motor control chopper
6. StallGuard4 load and stall detection for StealthChop
7. Cool Step current control for energy savings up to 75%
8. Low Power Standby to fit standby energy regulations

1. High speed printing
2. Supports high speed stepper motors up to 36V
3. Less vibration and noise
4. Offers much better printing experience
5. Smooth  mode switching

1. Bidirectional control for two brushed DC motor.
2. Control one unipolar/bipolar stepper motor.
3. Operating Voltage: DC 4V to 16V
4. Maximum Motor Current: 3A continuous, 5A peak
5. Buck-boost regulator to produce 5V output (200mA max).
6. Buttons for quick testing.

1. Dual channel, Bi-directional control motor driver
2. Support motor voltage from 2.5V to 9.5VDC
3. Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
4. 5V Output (200mA) to power the controller.
5. Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
6. Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
7. Regenerative Braking

1. Supply Voltage: 8.2 – 42 VDC.
2. Current Capacity : 2.2A max(24V).
3. Continuous current per phase: 1.5 A.
4. Minimum Logic voltage: 2.5V.
5. Maximum Logic Voltage: 5V.
6. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
7. Dimensions : 15 x 20 mm.
8. Weight: 4 gm.

1. Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
2. Operating voltage: 2.7‌‌ V to 10.8 V
3. Output current: 1.2 A continuous (2 A peak) per motor
4. Inputs are 3V- and 5V-compatible

1. In 64 subdivision or 128 subdivision to achieve a better ultra-quiet effect.
2. Operating voltage: 6V-36V, the proposed voltage is 12V.
3. The maximum current is 1.5A, the default is 0.8A.
4. Segment: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128.

1. Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
2. USB power supply and peripherals power phase are separate to protect computer security.
3. All the signals are to-isolate which can protect your computer security.
4. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
5. Wide input voltage range: 12-24V, and with anti-reverse function.
6. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.