- Both Analog and Digital Output
- Operating Voltage: 5VDC
- Compatible With M5 Core
- Adjustable Threshold via Onboard Potentiometer
-42%
Based on 0 reviews
Be the first to review “M5 Stack Earth Moisture Sensor Unit with Analog and Digital Output”
Related products
-
Basic Electronic Components, DIY Learning and Robot Kits, Sensors
L298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
-50%
Basic Electronic Components, DIY Learning and Robot Kits, SensorsL298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
- L298N Motor Driver Controller Module is a high power motor driver for driving DC and Stepper motors. It can control upto 4 DC motors, or 2 DC motors with directional and speed control. This motor driver is for robotics and mechatronics projects. The 150 RPM Dual Shaft BO Motor is a straight motor which gives good torque and RPM at lower operating voltages. It is a geared DC Motor. It is an alternative to metal gear DC motors. The 65MM Wheel is made up of standard grade rubber.
- L298N: Current Sense for each motor | Heatsink for better performance | Power-On LED indicator | Directional control | Speed control | High power motor || BO motor: Low density and inertia | Capability to absorb shock and vibration as a result of elastic compliance | Ability to operate with minimum or no lubrication | Relatively low coefficient of friction || Wheel: Car hub is reinforced nylon | Sturdy | Tire with sponge liner for more strength | With upgraded tire tread for greater friction
- Dimensions: L298N(LxWxH):44x44x28mm | Shaft length:7mm | Shaft Diameter:5.5mm | Motor(LxWxH):55x48x23mm | Diameter of wheel:65mm | Center Shaft Hole Diameter (mm):5.4 (Round edge) and 3.5 (Flat edge)
- The L298N motor driver is perfect for robotics and mechatronics projects. It can also be used for controlling motors from microcontrollers, switches, relays, etc. It is capable of driving DC and Stepper motors for micro mouse, line following robots, robot arms, etc. The BO motor is ideal for DIY enthusiasts. This motor set is inexpensive, small, easy to install and ideally suited for use in a mobile robot car. The 65mm wheel is only compatible with BO motor.
- L298N: Input Voltage:3.2V-40V DC | L298N Dual H-Bridge DC Motor Driver | Operating voltage:DC 5V-35V | Peak Current:2Amps | Speed Control:PWM | Control Signal input voltage range:0.3V≤Vin≤1.5V (Low), 2.3≤Vin≤Vss (High) | Max. power consumption:20W (when the temperature T=75℃) || BO Motor: Operating Voltage:3 to 12V | Current (without loading):40-180mA | RPM:100 | Output Torque:0.8 kgcm | Motor Design: L-shaped || Wheel: Loading Capacity (kg):2.5 | D hole For BO Motor (mm):6
SKU: n/a -
Uncategorized, Sensors
HC-SR501 Passive Infrared PIR Motion Sensor Module for Motion Detection Intruder Alert – 1 Piece
-25%
Uncategorized, SensorsHC-SR501 Passive Infrared PIR Motion Sensor Module for Motion Detection Intruder Alert – 1 Piece
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time is adjustable.
- Used for Motion Detection
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
SKU: n/a -
Sensors
3.5-5.5V Standard Active Buzzer Module For Arduino
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.This module is ideally suited to adding noise to your project and is compatible with a pin pitch of 2.54mm while functioning with microcontrollers such as the Arduino. This module lets you respond to programmatic changes with a lovely annoying buzzer that can be altered over a range of frequencies to ensure maximum irritation. To operate the I/O pin must receive a square wave to trigger the buzzer. This can be produced within all popular microcontrollers.Specification:- Working voltage: 3.5-5.5V
- Working current: <25mA
- PCB Dimension: 1.85 x 1.5 cm (L x W)
Feature:
- An active buzzer with a concussion internal source- so long as it will be called an energized
- The program easy to control- SCM can let a high-low sound- while passive buzzer did not.
- The Transistor drive module uses 8550
- With fixed bolt hole- easy installation- 2.6mm aperture.
Package included:
1 x Standard Active Buzzer ModuleSKU: n/a
There are no reviews yet.