- Uses I2C interface (Qwiic-enabled)
I2C Address: 0x70
2x Qwiic Connectors - Operating voltage range
1.62V – 3.6 V
Typically 3.3V if using the Qwiic cable
-15%
Related products
-
Sensors
HC-05 Bluetooth Wireless UART Module
HC-05 is a Bluetooth Transceiver Module and has TTL Output. HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. This Bluetooth module is a completely qualified Bluetooth V2+Enhanced Data Rate (EDR). It is 3Mbps Module with 2.4GHz radio transceiver and baseband. It has CSR Bluecore 04, an external single-chip Bluetooth system with CMOS technology and AFH, Adaptive Frequency Hopping, feature.
The HC-06 module is a slave only device. This means that it can connect to most phones and computers with Bluetooth but it cannot connect to another slave-only device such as keyboards and other HC-06 modules. To connect with other slave devices a master module would be necessary such as the HC-05 version which can do both master and slave.
Specification and Features:
- Voltage supply: 3.5v to 5v
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- With the integrated antenna and edge connector
- Sensitively: -80dBm
- RF Transmit Power: up to +4dBm
- Supported baud rate: 9600, 19200, 38400, 57600, 115200, 230400 and 460800
- Slave default baud rate: 9600
- Data bits: 8
- Stop bit: 1
- Parity: no parity
- A programmable input-output control
- Supported device: laptop, desktop, mobile, tablet
- Protocol: IEEE802.15.1
- Dormancy current: no dormancy.
- Bluetooth module HC-05 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Security: Authentication and encryption.
SKU: n/a -
Sensors
3.5-5.5V Standard Active Buzzer Module For Arduino
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.This module is ideally suited to adding noise to your project and is compatible with a pin pitch of 2.54mm while functioning with microcontrollers such as the Arduino. This module lets you respond to programmatic changes with a lovely annoying buzzer that can be altered over a range of frequencies to ensure maximum irritation. To operate the I/O pin must receive a square wave to trigger the buzzer. This can be produced within all popular microcontrollers.Specification:- Working voltage: 3.5-5.5V
- Working current: <25mA
- PCB Dimension: 1.85 x 1.5 cm (L x W)
Feature:
- An active buzzer with a concussion internal source- so long as it will be called an energized
- The program easy to control- SCM can let a high-low sound- while passive buzzer did not.
- The Transistor drive module uses 8550
- With fixed bolt hole- easy installation- 2.6mm aperture.
Package included:
1 x Standard Active Buzzer ModuleSKU: n/a -
Sensors
PIR Motion Detector Sensor Module
The HC-SR501 PIR Motion Detector Sensor Module is a pyroelectric device that detects motion by measuring changes in the infrared levels emitted by surrounding objects. This motion can be detected by checking for a high signal on a single I/O pin.
The module has an onboard pyroelectric sensor, conditioning circuitry, and a dome-shaped Fresnel lens. It has a delay time adjustment Potentiometer and sensitivity adjustment Potentiometer.
It is used to sense the movement of people, animals, or other objects. They are commonly used in burglar alarms and automatically-activated lighting systems. Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc.
Features:
- Compact size
- Infrared sensor: dual-element, low noise, high sensitivity
- Blockade time: 2.5s (Default)
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
SKU: n/a -
Basic Electronic Components, Electronic Components, Sensors
37 In 1 Sensors Set Kit For Arduino
It comprises 37 Pcs of essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product. This is the most complete performance starter kit with all the essential Arduino sensors.
FEATURES :
- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
Kit list:
- 1 x Active buzzer module
- 1 x Passive buzzer module
- 1 x Common cathode RED&GREEN LED module
- 1 x Two-color common cathode LED module
- 1 x Knock sensor module
- 1 x Shock switch sensor module
- 1 x Photoresistor sensor module
- 1 x Push button module
- 1 x Tilt switch module
- 1 x RGB LED module
- 1 x Infrared transmit module
- 1 x RGB colorful LED module
- 1 x Hydrargyrum switch sensor module
- 1 x Colorful auto flash module
- 1 x Magnet-ring sensor module
- 1 x Hall sensor module
- 1 x Infrared receive sensor module
- 1 x Analogy hall sensor module
- 1 x Magic ring module
- 1 x Rotate encode module
- 1 x Light break sensor module
- 1 x Finger pulse sensor module
- 1 x Magnetic spring module
- 1 x Obstacle avoidance sensor module
- 1 x Tracking sensor module
- 1 x Microphone sensor module
- 1 x Laser transmit module
- 1 x Relay module
- 1 x Analog temperature sensor module
- 1 x 18b20 temperature sensor module
- 1 x Digital temperature sensor module
- 1 x Linear hall Sensor module
- 1 x Flame sensor module
- 1 x High sensitive voice sensor module
- 1 x Humidity sensor module
- 1 x Joystick PS2 module
- 1 x Touch sensor module
Package Includes:
1 x Sensor module board set for Arduino(37 types in total)SKU: n/a
Reviews
There are no reviews yet