- Interface: I2C
- Power supply voltage: VM = 15V max
- Output current: Iout = 1.2A ( average ) / 3.2A ( peak )
- Standby control to save power CW / CCW / short brake / stop motor control modes
- Standby control mode-I2C mode: control TB6612’s STBY with I2C protocol
- IO mode: control TB6612’s STBY with Spin
-24%
Motors | Drivers | Pumps | Actuators
TB6612 D1 Motor Driver Shield
- Interface: I2C
- Power supply voltage: VM = 15V max
- Output current: Iout = 1.2A ( average ) / 3.2A ( peak )
- Standby control to save power CW / CCW / short brake / stop motor control modes
- Standby control mode-I2C mode: control TB6612’s STBY with I2C protocol
- IO mode: control TB6612’s STBY with Spin
₹1,289.00 ₹1,689.00
Based on 0 reviews
Be the first to review “TB6612 D1 Motor Driver Shield”
Related products
-
Motors | Drivers | Pumps | Actuators
12V DC 1/2″ Normally Closed Electric Solenoid Water Air Valve Switch
-38%
Motors | Drivers | Pumps | Actuators12V DC 1/2″ Normally Closed Electric Solenoid Water Air Valve Switch
12V DC Solenoid Water Air Valve Switch (Normally Closed) – 1/2″ controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid! This liquid valve would make a great addition to your robotic gardening project. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through.
The valve works with the solenoid coil which operates electronically with DC 12 volt supply. As it is a normally closed assembly, it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed.
Note: While Connecting the Valve in the Flow pipeline, you need to mind the Input and Output direction of the valve. It will work only if you connect it in the right direction. (Hint: Inside the value, at one side you will find the filter this is the input side of the value)
SKU: n/a -
Motors | Drivers | Pumps | Actuators
AEROKART INDIA 100RPM Dual Shaft BO Motor – Yellow – Pack Of 8
-38%
Motors | Drivers | Pumps | ActuatorsAEROKART INDIA 100RPM Dual Shaft BO Motor – Yellow – Pack Of 8
- The 100 RPM Dual Shaft BO Motor is a straight motor which gives good torque and RPM at lower operating voltages. It is a geared DC Motor. It is an alternative to metal gear DC motors.
- Low density | Lightweight | Low inertia | Capability to absorb shock and vibration as a result of elastic compliance | Ability to operate with minimum or no lubrication | Inherent lubricity | Relatively low coefficient of friction
- Shaft length : 7 mm Motor Design : L-Shaped Shaft Diameter : 5.5 mm Size : 55 x 48 x 23 mm
- The BO motor is ideal for DIY enthusiasts. This motor set is inexpensive, small, easy to install and ideally suited for use in a mobile robot car.
- Operating Voltage : 3 to 12V Current (without loading) : 40-180mA RPM : 100 Output Torque : 0.8 kg cm
SKU: n/a -
Motors | Drivers | Pumps | Actuators
TOWER PRO 9G MICRO SERVO MOTOR
The Micro Servo 9G is lightweight, high-quality and lightning-fast. The servo is designed to work with almost all the radio control systems. It is with excellent performance brings you to another horizon of flight. The SG90 mini servo with accessories is perfect for R/C helicopter, plane, car, boat and truck useFeatures:- Required Pulse: 3-5 Volt Peak to Peak Square Wave
- Operating Voltage: 4.8-6.0 Volts
- Operating Temperature Range: -10 to +60 Degree C
- Operating Speed (4.8V): 0.12sec/60 degrees at no load
- Operating Speed (6.0V): 0.10sec/60 degrees at no load
- Stall Torque (4.8V): 1.8kg/cm
- Stall Torque (6.0V): 2.4kg/cm
- 360 Modifiable: Yes
- Bearing Type: Ball Bearing
- Gear Type: Nylon Gears
- Connector Wire Length: 12″
- Dimensions: 22×11.5x27mm
- Weight: 11g
Package Content:
1 x TOWER PRO SG90 9G MICRO SERVO MOTOR
SKU: n/a -
Motors | Drivers | Pumps | Actuators
AEROKART INDIA 1pcs 12V 5 Kg-cm 200 RPM 6mm Shaft 5 Kg-cm Torque Geared DC Motor with 12V – 40V 10A PWM DC Motor Variable Speed Controlle
-30%
Motors | Drivers | Pumps | ActuatorsAEROKART INDIA 1pcs 12V 5 Kg-cm 200 RPM 6mm Shaft 5 Kg-cm Torque Geared DC Motor with 12V – 40V 10A PWM DC Motor Variable Speed Controlle
- DC Motor – Voltage: 6V to 12V; RPM : 200; Torque Range: 5 Kg-cm
- Input supply voltage: 10V – 40VDC ; Max. Current: 10A
- 1. Connect your DC motor (or DC load) to the motor terminals as indicated. 2. Connect a voltage of 10V-36V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit. It is recommended to add an appropriately rated fuse inline with the positive supply in order to protect the circuit from any possible short circuits. 3. You can now control the speed of the motor through potentiometer.
- Control power: 0.01~400W; Static current: 0.02 A (standby) PWM duty ratio:10%~100%; PWM frequency: 13 KHz
- Package include: 1 x 200 RPM DC Motor, 1 x 10A PWM
SKU: n/a
There are no reviews yet.