- Working voltage: 5.0±0.1V DC
- Detection Gas: CO2
- Output signal: UART(TTL interface level 3.3V), PWM
- Range: CO2(400-2000ppm/400-5000ppm)
- Gold-plated Chamber
Related products
-
Sensors
5V Passive Buzzer Acoustic Component Mini Alarm Speaker for Electronic Project (Pack of 10)
-25%Sensors5V Passive Buzzer Acoustic Component Mini Alarm Speaker for Electronic Project (Pack of 10)
0 out of 5(0)- Working voltage: 3.5-5.5V
- Loud audible pleasant tone
- Consumes very less power, high efficiency
- Useful in projects, toys, dash boards, warning signals
- Small and light high power-dissipation capability low frequency high efficiency
SKU: n/a -
Basic Electronic Components, Sensors
Eye Blink Sensor Project Kit
0 out of 5(0)The Eye-Blink sensor works by illuminating the eye and eyelid area with infrared light, then monitoring the changes in the reflected light using a phototransistor and differentiator circuit.
This includes Arduino Nano, Eye Blink sensor, Buzzer, Battery, Clip Connector, and Switch.
Eye Blink sensor senses the eyeblink using infrared. The Variation Across the eye will vary as per eye blink. If the eye is closed the output is high otherwise the output is low.
Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality as the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one.
A Standard Active Buzzer Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.
This is a general 9v Battery for all your project and application needs.
A clip Connector is used to connect a 9V battery to the application. This snap power cable to DC 9V clip male line battery adapter for mostly used to power Arduino boards.
Rocker switch is Rocker Switch SPST ON/OFF Microswitch.
SKU: n/a -
DIY Learning and Robot Kits, Electronic Modules, Sensors
Arduino Uno with LCD and Keypad
0 out of 5(0)Arduino UNO-based kit provides an open-source electronics prototyping platform based on flexible, easy-to-use hardware and software. It contains all of the essential components required to start programming with the Arduino Uno board.
This combo includes Arduino Uno with cable, 4×4 membrane keypad, 16×2 LCD Display, 3 types of Jumper Wires.
Arduino Uno R3 Compatible Board is a microcontroller board that is based on the ATmega328. Arduino Uno has 14 digital input or output pins(where 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It has everything needed to support the microcontroller, you need to simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.
LCD1602 Parallel LCD Display provides a simple and cost-effective solution for adding a 16×2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display that has a very clear and high contrast.
Matrix Keypad 4 X 4 has 16 buttons, arranged in a telephone-line 3×4 grid with a column of 4 characters (A, B, C, and D). The keys are connected into a matrix, hence only 8 microcontroller pins (4-columns and 4-rows) are required to scan the pad.
Applications:
- Security System
- Calculator
- Device Control
SKU: n/a -
Sensors
iR Avoidance Proximity Sensor E18-D80NK For 5V Switch Detect 3-80cm For Robotics
0 out of 5(0)- Model: E18-D80NK
- This is a set of transmitter and receiver in one of the photoelectric sensor
- A detection distance can be adjusted according to the requirements
- The production line of automatic counting equipment goods
- Diameter: 17MM
SKU: n/a
Reviews
There are no reviews yet