- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V).
- Max current draw: 15mA @ 5V.
- Working Flow Rate: 1 to 30 Liters/Minute.
- Maximum water pressure: 2.0 MPa.
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min).
-17%
Sensors
YF-S201 Water Flow Measurement Sensor with 1-30Liter/min Flow Rate – White
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V).
- Max current draw: 15mA @ 5V.
- Working Flow Rate: 1 to 30 Liters/Minute.
- Maximum water pressure: 2.0 MPa.
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min).
₹482.00 ₹582.00
Related products
-
Sensors
Infrared Obstacle Avoidance IR Sensor Module With LED Indicators – LM393 Chip – Proximity Sensor – Pack Of 3
-56%
SensorsInfrared Obstacle Avoidance IR Sensor Module With LED Indicators – LM393 Chip – Proximity Sensor – Pack Of 3
- Infrared Obstacle Avoidance IR Sensor Module (Active Low) contains a pair of infrared transmitting and receiving tubes. When the transmitted light waves are reflected back, the reflected IR waves will be received by the receiver tube. The onboard comparator circuitry does the processing and the green indicator LED comes to life.
- Mounting hole | Adjustable Range Detection | LED Indicators | Built-in Ambient Light Sensor | Infrared transmitting and receiving tubes | Onboard comparator circuitry | Easy to assemble | Easy to use
- LxWxH : 48 x 14 x 8 mm
- The IR sensor module can be widely used for robot obstacle avoidance, obstacle avoidance car assembly line count, black-and-white line tracking and many other occasions. This sensor module can be used for obstacle detection in autonomous robots and cars, in positional feedback for control system, industrial safety system, wheel encoder etc.
- Main Chip : LM393 Operating Voltage (VDC) : 3.6 ~ 5 Average Current Consumption (mA) : 0.06 Detection Angle : 35 ° Distance Measuring Range : 2 – 30 cm
SKU: n/a -
Sensors
Mini Solderless Breadboard -170 Tie Points for Arduino,DIY Project
This is a mini solderless prototype breadboard 170 points for the Arduino shield.
Description:
- Material: ABS
- Mini Solderless Breadboard
- Tie-point: 170Completely reusable
- Colored coordinates for easy component placement
- Size:45x34x9mm(1.771.34×0.35 inch)
- Color: Red, Black, White, Blue, green (It will be shipped randomly)
Package Includes:
1 x Mini breadboard
SKU: n/a -
Basic Electronic Components, Sensors
Eye Blink Sensor Project Kit
The Eye-Blink sensor works by illuminating the eye and eyelid area with infrared light, then monitoring the changes in the reflected light using a phototransistor and differentiator circuit.
This includes Arduino Nano, Eye Blink sensor, Buzzer, Battery, Clip Connector, and Switch.
Eye Blink sensor senses the eyeblink using infrared. The Variation Across the eye will vary as per eye blink. If the eye is closed the output is high otherwise the output is low.
Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality as the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one.
A Standard Active Buzzer Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.
This is a general 9v Battery for all your project and application needs.
A clip Connector is used to connect a 9V battery to the application. This snap power cable to DC 9V clip male line battery adapter for mostly used to power Arduino boards.
Rocker switch is Rocker Switch SPST ON/OFF Microswitch.
SKU: n/a -
Sensors
3.5-5.5V Standard Active Buzzer Module For Arduino
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.This module is ideally suited to adding noise to your project and is compatible with a pin pitch of 2.54mm while functioning with microcontrollers such as the Arduino. This module lets you respond to programmatic changes with a lovely annoying buzzer that can be altered over a range of frequencies to ensure maximum irritation. To operate the I/O pin must receive a square wave to trigger the buzzer. This can be produced within all popular microcontrollers.Specification:- Working voltage: 3.5-5.5V
- Working current: <25mA
- PCB Dimension: 1.85 x 1.5 cm (L x W)
Feature:
- An active buzzer with a concussion internal source- so long as it will be called an energized
- The program easy to control- SCM can let a high-low sound- while passive buzzer did not.
- The Transistor drive module uses 8550
- With fixed bolt hole- easy installation- 2.6mm aperture.
Package included:
1 x Standard Active Buzzer ModuleSKU: n/a
Reviews
There are no reviews yet