- High-performance STM32H743 Processor with more computing power & RAM
- New cost-effective design with the low-profile form factor
- A newly designed integrated vibration isolation system to filter out high-frequency vibration and reduce noise to ensure accurate readings
- IMUs are temperature-controlled by onboard heating resistors, allowing the optimum working temperature of IMUs
Holybro Pix32 v6 Flight Controllers FC Module Standard Set
- High-performance STM32H743 Processor with more computing power & RAM
- New cost-effective design with the low-profile form factor
- A newly designed integrated vibration isolation system to filter out high-frequency vibration and reduce noise to ensure accurate readings
- IMUs are temperature-controlled by onboard heating resistors, allowing the optimum working temperature of IMUs
₹30,185.00 ₹32,185.00
Based on 0 reviews
Be the first to review “Holybro Pix32 v6 Flight Controllers FC Module Standard Set” Cancel reply
Related products
-
Flight Controller & Accessories
Radiolink Pixhawk Flight controller board
0 out of 5(0)Radiolink Has optimised its pixhawk flight controller PCB layout and height hold with the barometer sensor MS5611. It is a highly stable flight controller that comes from the radiolink. This controller provides more stable flight performance even at high speed. It integrated the newest 32-bit chip technology and high-end sensors, this is absolutely one of the best flight controllers for quadcopters.
Feature:
- Multi-sound buzzer interface support.
- Multiple flight modes, support for self-stability, height-set, hover, sports, freestyle, circling, following, return, guidance, automatic, and all-powerful.
- Abundant connectivity options for additional peripherals (GPS, I2C, SPI).
- 14 PWM / servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible).
- Providing a multi-sound buzzer interface.
- Multiple flight mode switches freely, Helicopter, Fixed-wing, Multi-rotor, Model Car.
- All interfaces are fully tested and accurately detected by an automatic detection system, avoiding bad interfaces leading to flight control installation unsuccessfully.
- Support DSM Spektrum receiver.
- Advanced 32-bit CortexM4 ARM high-performance processor, and 32-bit STM32STMF100 failsafe co-processor.
- Equipped with buzzer, 4G memory card, safety switch and power module.
TECHNICAL Processor 32bit 32F427 ARM Cortex M4 Core + FPU (floating point unit) Frequency 168 MHZ Memory Size 2 MB Flash RAM Size 256 KB Sensor ST Micro L3GD20H 16 bit gyroscope FLIGHT CONTROLLER Sensors MEAS MS5611 barometer Hardware Details Barometer sensor MS5611 Three-axis digital gyroscope IST8310 triaxial accelerometer(E-compass) IST8310 Six-axis accelerometer(Gyro) MPU6000 FRAM FM25V02
(256Kb)All Functions Automation Software Testing System Have SKU: n/a -
Flight Controller & Accessories
KK2.1.5 LCD Flight Controll Board for FPV Racing Drone | e | kk flight controller
-54%Flight Controller & AccessoriesKK2.1.5 LCD Flight Controll Board for FPV Racing Drone | e | kk flight controller
0 out of 5(0)The kk 2.1.5 flight controller is next big evolution of the first generation KK flight controller boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!The KK2.1.5 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap.Description:
Item number:Â KK2.1.5Size: 51mm x 51mm x 12mmWeight: 21 gram (Inc Piezo buzzer)IC: AtmegaGyro/Acc: InvenSense Inc.Auto-level: YesInput Voltage: 4.8-6.0VAVR interface: standard 6 pinSignal from Receiver: 1520us (5 channels)Signal to ESC: 1520usSKU: n/a -
Flight Controller & Accessories
Pixhawk 2.4.8 PX4 32 Bit Flight Controller with Safety Switch and Buzzer for Drone High Quality
-41%Flight Controller & AccessoriesPixhawk 2.4.8 PX4 32 Bit Flight Controller with Safety Switch and Buzzer for Drone High Quality
0 out of 5(0)Characteristics:
- Compatible with Alexmos2.2 or firmware below, compatible with the newest firmware BruGi_050 German, standard Russian2.2 firmwareTips
- A new generation of strong input control 32-bit processor, a circuit board with PX4FMU + PX4IO
Specifications:
- 32-bit Pixhawk PX4 Autopilot Open Code Flight Controller V2.4.8
- 2 bit 1.32 STM32F427 flash Cortex M4, with the floating-point hardware processing unit
- 2 main frequency: 256 K, RAM 168 MHZ
- 32-bit processor STM32F103 backup co
Sensors:
- Â L3GD20 3-axis 16-bit digital gyroscope
- Â LSM303D 14/3 Axis Accelerometer Magnetometer
- MPU6000 6-axis accelerometer / magnetometer
- Â MS5611 high precision barometer
Interface:
- 5 UART 1 High Voltage compatible, 2 with hardware flow control
- 2 CAN
- DSM / DSM-XÂ Spektrum compatible satellite receiver input
- SBUSÂ input and output compatible
- PPM signal input
- RSSI (PWM or input voltage)
- I2C
- SPI
- 3.3 and 6.6 VADC inputs
- external US MICRO
Package includes:
1 XÂ 2.4.8 Pixhawk main control with shell
1 XÂ Â Safety switch
1 XÂ Buzzer
1 XÂ Memory Card
Connection Wire
SKU: n/a -
Flight Controller & Accessories
OpenPilot CC3D EVO Flight Controller STM32 for RC Drone FPV Racing
-30%Flight Controller & AccessoriesOpenPilot CC3D EVO Flight Controller STM32 for RC Drone FPV Racing
0 out of 5(0)CC3D Flight Controller Hardware Features
Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac, and Linux.
Direct high-speed USB support with no drivers required, a truly plug-and-play device.
Spektrum satellite receiver support.
Futaba S-BUS hardware support.
Innovative Flexi-port technology for superior port flexibility.
4Mbits on-board EEPROM for configuration storage.Note: Please don’t flash/Update the Default firmware. Updated or new firmware may cause a problem of connectivity with PC/Laptop.
Software for configuration:Â Openpilot
You can also use Software for configuration:Â Librepilot
Flexiport
CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C
and a single serial port or dual serial ports, according to your connectivity needs.Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally, for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with a bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.The OpenPilot project, whist still young, it trying to make Open Source much more user-friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!
Sensors and Components
3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.
Simultaneous support for multiple receivers.
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
Onboard USB connectivity for easy configuration.
USB and serial telemetry and configuration
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500HzPackage included:
1 x CC3D EVO Flight Controller And CablesSKU: n/a
There are no reviews yet.