Special Offer
-
-
-
FPV Cameras
Caddx Air Unit Polar starlight Digital HD FPV system
- Transmitter Power(EIPP): FCC/SRRC: <30dBm; CE: <14dBm
- I/O Interface: USB-C,MMCX,3-in-1 port, micro SD card slot
- Operating Temperature Range: 0°to 40°C(32°to 104°F)
- Max.Transmission Distance: FCC/SRRC:4km;CE:0.7km
- Image Sensor: 1/1.8″ Inch 2.3Mega starlight sensor
SKU: n/a -
Flight Controller & Accessories
35A 4in1 ESC & F4 V3S Plus Flight Control V3.5 V3 S Built-in Image Filtering OSD
-8%Flight Controller & Accessories35A 4in1 ESC & F4 V3S Plus Flight Control V3.5 V3 S Built-in Image Filtering OSD
- This is combo kit of Flight controller & ESC
- High performance & efficient flight controller & ESC
- Light weight, Easy to connect
- Compact in size
- Flight controller comes with ARM processor
- ESC is build to give best performance
SKU: n/a
-
Flight Controller & Accessories
Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot – Good Quality
-51%Flight Controller & AccessoriesPixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot – Good Quality
- Supply Voltage: 7V.
- Processor: 32 Bit Cortex M4 Core
- Bus interface (UART, I2C, SPI, CAN).
- Firmware: Mission planner.
- Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer
- Micro SD card to record flight data.
SKU: n/a -
(ESC) Drone Speed Controller
20A Bidirectional Digital ESC
This 20A Bidirectional Digital ESC adopts imported components. It features small size, strong power, low self-heating, and fast response speed. There is no need to calibrate the throttle position. Question)This ESC is a digital ESC that automatically detects throttle stroke and neutral position of the throttle and does not require a remote control to set the switch. If using onboard, please do a good job of sealing and heat dissipation. (It is recommended to use 704 silicon to install Esc.) It is suitable for nesting boats, remote control cars, etc. Suitable for a wide variety of scenarios- Input voltage: 2-4S
- Nominal output current: 20A
- Maximum output current; 30A
- Forward and reverse output power ratio 1: 1
SKU: n/a -
Electronic Components
300 RPM Dual Shaft BO Motor-Straight
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 300 RPM
- Rated Torque: 0.35 Kgcm
SKU: n/a -
Electronic Modules, Electronic Modules and Displays
1Pcs 2A USB 18650 Lithium Li-ion Battery Charger Module Boost 3.7V to 5V 9V 12V
-34%Electronic Modules, Electronic Modules and Displays1Pcs 2A USB 18650 Lithium Li-ion Battery Charger Module Boost 3.7V to 5V 9V 12V
- Can be used for multimeter, converted to lithium battery charging
- Note: The OUT+Port can output an adjustable voltage
- Input voltage: 4.5-8V DC Output voltage: 4.3-27V DC,Charging voltage: 4.2V DC
- Charging current: Max. 1A Discharging current: Max. 2A
- Package Includes: 1x Step Up Boost Module
SKU: n/a -
DIY Kits, DIY Learning and Robot Kits, Drone Accessories, Drone Frame and Accessories, Drone Parts
XYQ-2 DIY Drone Mini Toy Drone Aircraft With Remote Wooden Assembly Mini Drone Quadcopter
-17%DIY Kits, DIY Learning and Robot Kits, Drone Accessories, Drone Frame and Accessories, Drone PartsXYQ-2 DIY Drone Mini Toy Drone Aircraft With Remote Wooden Assembly Mini Drone Quadcopter
This quadcopter kit is a DIY Drone, the majority of the pieces of this one-of-a-kind wooden Drone toy are made of wood! It’s cool, light, classic, and well-designed. Because this drone toy is a DIY aircraft, you can assemble all parts together to make your own mini drone.
Features:
Functions: Sideward flight, turn left/right, up/down, forward/backward, altitude hold, one key takeoff/landing, 3D flip, headless mode, one key returnWith attractive headless mode, completely solving pilot loss-of-orientation problems. Altitude hold: With a built-in barometer, the aircraft will fly to a certain height when taking off.One-key taking off/landing/stop makes the operation more convenient and it is very suitable for novice operation.With one key automatic return function, the plane can find its way home easily. SPECIFICATIONSMaterial WoodModel XYQ-2Drone Battery Li-Ion 600mAhRemote Control Battery Li-Ion 500mAhFlight Height <120mFrequency 2.4GHzSKU: n/a -
Drone Accessories, DRONE COMBO, Drone Frame and Accessories, Drone Gimbal Accessories, Drone Kit, Drone Motor, Drone Parts, Drone Transmitter and Receiver, Flight Controller & Accessories, FPV Antennas and Trans-Receivers, FPV Cameras, GPS Modules, Propellers
AEROKART INDIA UAV FULL CARBON FIBRE FRAME V650 V.22
-31%Drone Accessories, DRONE COMBO, Drone Frame and Accessories, Drone Gimbal Accessories, Drone Kit, Drone Motor, Drone Parts, Drone Transmitter and Receiver, Flight Controller & Accessories, FPV Antennas and Trans-Receivers, FPV Cameras, GPS Modules, PropellersAEROKART INDIA UAV FULL CARBON FIBRE FRAME V650 V.22
AEROKART INDIA UAV FRAME V650 V.22 is being discontinued and will be replaced with the improved hexacopter drone, the Aurelia X4 Standard. Please read further on this page about all product upgrades.
- Built, Tested, and Configured Tarot 650 v2.2
- Carry Specialized Payloads With Ease
- Carry Up To 3.3 lb (1.5 kg) Payload UPTO.
- Up To 2 mi (3.2 km) Range & 25 Minute Flight Time
- Powered By Open-Source Pixhawk & Ardupilot / PX4
- Can Be Customized Depending On Customer Requirements – Ask Us!
- Global International Shipping!
Looking for a larger option that carries more weight? Check out our Aurelia X6 Standard Ready To Fly, Aurelia X6 Pro Ready To Fly, or the largest drone with the largest payload capacity.
SKU: n/a -
Flight Controller & Accessories
Naze32 10DOF Flight Control Board
- Axis: 2000 degrees/second 3-axis MEMS gyro.
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line.
- Built-in FrSky telemetry inverter (shared w/main port).
- A modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Onboard MicroUSB for setup and configuration.
- Multi WiFi-based configuration software for easy setup.
SKU: n/a
-
Drone Accessories, Propellers
1045 Propeller 10in 10×4.5 For Drone
2 x 1045 Propellers in a set. One propeller that rotates clockwise and one that rotates anticlockwise are included in the kit, along with two propeller shaft adapters. The propeller can be used with motors of various shaft diameters thanks to the adapters. With a rating of 800-2200 kV, this 1045 propeller can be utilised with brushless motors. This propeller provides smooth flights with longer flying periods ideal for FPV and aerial photography with a low kV motor (800–1400 kV). This propeller’s high kV motor (more than 1200 kV) provides swift flights ideal for acrobatic performances. With our A2212 1000KV, 1400KV, 1800KV, and 2200KV motors and our 30A ESC, this propeller is compatible.
Item name: 1045 PropellerDiameter: 10inPitch: 4.5inPropeller diameter: 25.4cmCentre bore diameter : 6mm front and 9mm reverse side.Centre seat TH: 6mmWeight: about 14g/pairColor: black, red, yellow, green, orange.Usage: for quadcopter and multirotorPackage included:1 x CW Propeller1 x CCW PropellerSKU: n/a -
LDR
5800B Light Dependent Resistor (LDR) White Color
The 5800B Light Dependent Resistor (LDR) White Color is a photoresistor (or light-dependent resistor, LDR, or photo-conductive cell). Which is a light-controlled variable resistor. The resistance of a photoresistor decreases with increasing incident light intensity; in other words, it exhibits photoconductivity. A photoresistor is made of a high resistance semiconductor.
Photoresistors are Semiconductor devices that use light energy to control the flow of electrons, and hence the current flowing through them. When the light level decreases, the resistance of the LDR increases. As this resistance increases in relation to the other Resistor; which has a fixed resistance, it causes the voltage dropped across the LDR to also increase. When this voltage is large enough (0.7V for a typical NPN Transistor), it will cause the Transistor to turn on.
when the light falls on its surface, then the material conductivity reduces and also the electrons in the valence band of the device are excited to the conduction band.
SKU: n/a -
Basic Electronic Components, Capacitor, Electronic Components
1.5F – 5.5V – Super Capacitor
Super capacitors are perfect for applications where the capacity of a standard electrolytic capacitor is too small and a rechargeable battery is bigger than needed. This 1.5F capacitor will run an LED / Arduino board for 15-20mins
Features:
- Capacitance : 1.5 F
- Maximum operating voltage: 5.5 V
- Body shape: Coin type(multi-layer structure)
- Tolerance on capacitance: -20 to 80%
- Internal resistance(max.) : 30 ohms
- Category temperature range: -25?C to 70?C
SKU: n/a -
Basic Electronic Components, Electronic Components, Sensors
37 In 1 Sensors Set Kit For Arduino
It comprises 37 Pcs of essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product. This is the most complete performance starter kit with all the essential Arduino sensors.
FEATURES :
- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
Kit list:
- 1 x Active buzzer module
- 1 x Passive buzzer module
- 1 x Common cathode RED&GREEN LED module
- 1 x Two-color common cathode LED module
- 1 x Knock sensor module
- 1 x Shock switch sensor module
- 1 x Photoresistor sensor module
- 1 x Push button module
- 1 x Tilt switch module
- 1 x RGB LED module
- 1 x Infrared transmit module
- 1 x RGB colorful LED module
- 1 x Hydrargyrum switch sensor module
- 1 x Colorful auto flash module
- 1 x Magnet-ring sensor module
- 1 x Hall sensor module
- 1 x Infrared receive sensor module
- 1 x Analogy hall sensor module
- 1 x Magic ring module
- 1 x Rotate encode module
- 1 x Light break sensor module
- 1 x Finger pulse sensor module
- 1 x Magnetic spring module
- 1 x Obstacle avoidance sensor module
- 1 x Tracking sensor module
- 1 x Microphone sensor module
- 1 x Laser transmit module
- 1 x Relay module
- 1 x Analog temperature sensor module
- 1 x 18b20 temperature sensor module
- 1 x Digital temperature sensor module
- 1 x Linear hall Sensor module
- 1 x Flame sensor module
- 1 x High sensitive voice sensor module
- 1 x Humidity sensor module
- 1 x Joystick PS2 module
- 1 x Touch sensor module
Package Includes:
1 x Sensor module board set for Arduino(37 types in total)SKU: n/a -
IoT and Wireless, xBee Zigbee module
Zigbee XBee Module S2C 802.15.4 2mW with Wire Antenna XB24CZ7WIT-004
-34%IoT and Wireless, xBee Zigbee moduleZigbee XBee Module S2C 802.15.4 2mW with Wire Antenna XB24CZ7WIT-004
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with onboard microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
SKU: n/a -
DIY Kits, DIY Learning and Robot Kits, Drone Accessories, Drone Frame and Accessories, Drone Parts
XYQ-2 DIY Drone Mini Toy Drone Aircraft With Remote Wooden Assembly Mini Drone Quadcopter
-17%DIY Kits, DIY Learning and Robot Kits, Drone Accessories, Drone Frame and Accessories, Drone PartsXYQ-2 DIY Drone Mini Toy Drone Aircraft With Remote Wooden Assembly Mini Drone Quadcopter
This quadcopter kit is a DIY Drone, the majority of the pieces of this one-of-a-kind wooden Drone toy are made of wood! It’s cool, light, classic, and well-designed. Because this drone toy is a DIY aircraft, you can assemble all parts together to make your own mini drone.
Features:
Functions: Sideward flight, turn left/right, up/down, forward/backward, altitude hold, one key takeoff/landing, 3D flip, headless mode, one key returnWith attractive headless mode, completely solving pilot loss-of-orientation problems. Altitude hold: With a built-in barometer, the aircraft will fly to a certain height when taking off.One-key taking off/landing/stop makes the operation more convenient and it is very suitable for novice operation.With one key automatic return function, the plane can find its way home easily. SPECIFICATIONSMaterial WoodModel XYQ-2Drone Battery Li-Ion 600mAhRemote Control Battery Li-Ion 500mAhFlight Height <120mFrequency 2.4GHzSKU: n/a
Products Grid
Best Sellers
Recently Added
Caddx Air Unit Polar starlight Digital HD FPV system
35A 4in1 ESC & F4 V3S Plus Flight Control V3.5 V3 S Built-in Image Filtering OSD
35A 4in1 ESC & F4 V3S Plus Flight Control V3.5 V3 S Built-in Image Filtering OSD
2.4G 4CH Receiver Compatible with D8 Receiver w/ PWM Output
25x25x8mm 28db High Gain 5cm Length Built-in Ceramic Active GPS Antenna for NEO-6M NEO-7M NEO-8M
25x25x8mm 28db High Gain 5cm Length Built-in Ceramic Active GPS Antenna for NEO-6M NEO-7M NEO-8M
Raspberry Pi 4 Model-B with 8 GB RAM
Raspberry Pi 4 Model B 2GB Starter Kit
With the new upgrade to the Pi family, this is a complete starter kit of Raspberry Pi 2GB with all the mandatory accessories. These include products,
This combo has been made, keeping in mind the Raspberry Pi 4 Model B’s upgraded products so you can get it all in one go. So get it quickly and explore the world of Raspberry Pi 4.
Raspberry Pi 4 Model-B with 1 GB RAM
Raspberry Pi 4 Model-B with 1 GB RAM variant has been discontinued from Raspberry Pi Officials. Now 2GB RAM variant is available at the Same cost of 1GB. Below is the link for 2GB RAM Variant
Raspberry Pi 4 Model-B with 2 GB RAM
Introducing Orange Raspberry Pi Kits
Stuck in a never-ending cycle of learning Sensors, Micro-controllers, microprocessors, and communication protocols but not gaining any knowledge? Let us introduce you to Orange premium kits. These high-quality kits comes with free e-booklet and blogs to help you learn faster.