-
Drone Frame and Accessories, Drone Parts, Propellers
MADE IN INDIA 10X5X3(CCW-CW) Black-Glass Fiber Reinforced Nylon for FPV in India
-28%
Drone Frame and Accessories, Drone Parts, PropellersMADE IN INDIA 10X5X3(CCW-CW) Black-Glass Fiber Reinforced Nylon for FPV in India
1. 10-inch Diameter with 5 Pitch for optimal balance between thrust and efficiency
2. Tri-Blade Design for increased thrust, stability and rigidity
3. Made from Glass Fibre Reinforced Nylon for superior durability and performance
4. Lightweight Build – only 23 gm +- 5%, reduces load on motors
5. 18 mm Hub Diameter, 9 mm Hub Thickness and 5 mm Shaft CompatibilitySKU: n/a -
DIY Kits, DIY Learning and Robot Kits
Combo of Power Supply Module with Jumper Wire and Battery Clip, 830 & 400 tie-Points Breadboard Kit for Arduino
-24%
DIY Kits, DIY Learning and Robot KitsCombo of Power Supply Module with Jumper Wire and Battery Clip, 830 & 400 tie-Points Breadboard Kit for Arduino
- Wire Type: 40 pin Male to Male Jumper Wire
- Breadboard Power Supply Module
- Module: Compatible with 5V, 3.3V
- 9V battery clip connector
- Clip connector with 3.5mm jack
- 400 & 830-point half-size Solderless breadboard
SKU: n/a -
Uncategorized
Intel® RealSense™ Depth Camera D435IF
Model Depth Camera D435if Features Use environment: Indoor/Outdoor Ideal Range: .3 m to 3 m Depth Depth technology: Stereoscopic Minimum Depth Distance (Min-Z) at Max Resolution: ~28 cm Depth Accuracy: <2% at 2 m(2) Image sensor technology: Global Shutter Depth Field of View (FOV): 87° × 58°(1) Depth output resolution: Up to 1280 × 720 Depth frame rate: Up to 90 fps Filter Depth Filter IR Pass RGB Filter IR Cut RGB RGB frame resolution: Up to 1920 × 1080 RGB frame rate: 30 fps RGB sensor technology: Rolling Shutter RGB sensor FOV (H × V): 69 × 42°(1) RGB sensor resolution 2 MP Major Components Camera module: Intel RealSense Module D430 + RGB Camera Vision Processor Board: Intel RealSense Vision Processor D4 Physical Form factor: Camera Peripheral Connectors: USB‑C* 3.1 Gen 1* Length × Depth × Height: 90 mm × 25.8 mm × 25 mm Mounting mechanism:
- One 1/4‑20 UNC thread mounting point
- Two M4 thread mounting points
SKU: n/a -
-
ARM Microcontroller, AVR Development Board, Development Boards
Cora Z7: Zynq-7000 Single Core for ARM/FPGA SoC Development
-69%
ARM Microcontroller, AVR Development Board, Development BoardsCora Z7: Zynq-7000 Single Core for ARM/FPGA SoC Development
The Cora Z7 is our most cost-optimized SoC development board featuring the power and flexibility of AMD’s Zynq®-7000 SoC family.
Featuring Arduino™ headers, 1Gbps Ethernet, an onboard analog-to-digital converter, and Pmod ports, the Cora Z7 can be used in a variety of embedded applications. The Zynq-7000(S) SoC family integrates the software programmability of an ARM®-based processor with the hardware programmability of an FPGA, delivering cost-optimized system integration. At such a friendly price point, the Cora Z7 is a great development board to get started with Zynq-based designs.
The Cora Z7 is supported by AMD’s Vivado ML, including the free Vivado ML Standard Edition. You can also interact with the processing system (PS) with AMD Vitis Unified Software Platform and PetaLinux Tools.
SKU: n/a -
DRONE COMBO, Drone Kit, Drone Parts
Premium Hexacopter Drone Combo Set with Pixhawk For Flower Dropping Drone
-38%
DRONE COMBO, Drone Kit, Drone PartsPremium Hexacopter Drone Combo Set with Pixhawk For Flower Dropping Drone
1 x Set Of Radiolink Pixhawk 2.4.8 Flight controller with accessories
1 x FlySky FS-i6 2.4G 6CH AFHDS Transmitter With FS-iA6B Receiver for RC FPV Drone
1 x DJI F550 Frame
1 x Landing Gear
6 x Readytosky 920kv motor(3cw + 3ccw)
6 x BLHeli LittleBee 30A ESC (OPTO) 2-6SLipo
1 x power module for Pixhawk
1 x Ubolx neo M8N gps
1 x GPS stand|
3 x 1045 Carbon fiber propeller
1 x Mg996 metal gear servo
1 x Lm2596 power supply for servo
1 x Shock absorberSKU: n/a -
DRONE COMBO, Drone Kit, Drone Parts
FPV DRONE KIT Kit with Crossflight
1 x QAV250 V2 Carbon Fiber Frame
1 xFlySky FS-i6 Transmitter
4 x BLHeli LittleBee 30A ESC
4 x Readytosky 2205 2300KV Brushless Motors ( 2 CW – 2 CCW )
4 x 5045 3-Blade Propellers
1 x Radiolink crossflight Flight Controller
1 x Readytosky 20cm Nylon Strap Belt for RC Lipo Battery
1 x Shock Absorber Set
SKU: n/a -
Uncategorized
Quadcopter Drone Combo with Pixhawk Kit for beginner (Motor + ESC + Propeller + Flight Controller + Frame + TX-RX Flysky FSi6+ Power module + Belt)
-15%
UncategorizedQuadcopter Drone Combo with Pixhawk Kit for beginner (Motor + ESC + Propeller + Flight Controller + Frame + TX-RX Flysky FSi6+ Power module + Belt)
1 x Pixhawk Flight controller board
1 x DJI F450 Quadcopter Frame Kit
4 x A2212 1000KV Brushless Motor For RC Airplane / Quadcopter
4 x 30A Brushless ESC
2 x 1045 Propeller 10in 10×4.5 For Drone
1 x FlySky FS-i6 2.4G 6CH AFHDS Transmitter With FS-iA6B Receiver
1 x APM Pixhawk Power Module with XT60
1 x Nylon Strap Belt for RC Lipo Battery
1 x 3D printed Shock Absorber Anti-vibration Set for APM Pixhawk
SKU: n/a -
Basic Electronic Components
ADS1231IDR – 24-Bit 80SPS 1-Ch Delta-Sigma ADC IC
The ADS1231IDR – 24-Bit 80SPS 1-Ch Delta-Sigma ADC IC in an SOIC package offers precise analog-to-digital conversion with a resolution of 24 bits and a sampling rate of 80 samples per second (S/s). It operates with an input range of 3V to 5.3V, providing low power consumption of just 5mW. This ADC features a bipolar polarity and interfaces via SPI. It is designed for use in applications requiring high-resolution conversion, such as in measurement and control systems. The device is lead-free, RoHS compliant, and has a maximum operating temperature of 85°C and a minimum operating temperature of -40°C.
Features :
Resolution: 24 bits for high-precision conversion.
Sampling Rate: 80 samples per second (S/s).
Interface: SPI (Serial Peripheral Interface).
Operating Voltage: 3V to 5.3V, with a nominal supply of 5V.
Low Power: Power consumption of 5 mW.
Temperature Range: -40°C to 85°C.SKU: n/a -
Basic Electronic Components
MCP3208-CI/P-MICROCHIP-MCP3208-CI/P-Analogue to Digital Converter, 12 bit, 100 kSPS, Pseudo Differential, Single Ended, Serial, SPI
-57%
Basic Electronic ComponentsMCP3208-CI/P-MICROCHIP-MCP3208-CI/P-Analogue to Digital Converter, 12 bit, 100 kSPS, Pseudo Differential, Single Ended, Serial, SPI
The MCP3208-CI/P is an 8 channel, 12bit Analogue to Digital Converter (ADC) with SPI interface in 16 pin DIP package. This ADC combines high performance and low power consumption in a small package by making it as an ideal for embedded control applications. The MCP3208 features successive approximation register (SAR) architecture with onboard sample and hold circuitry allowing 12bit ADC capability to be added to any PIC microcontroller. It is programmable to provide four pseudo differential input pairs or eight single ended inputs. Differential nonlinearity (DNL) is specified at ±1LSB and integral nonlinearity (INL) is ±2LSB. Communication with devices is accomplished using simple serial interface compatible with SPI protocol. Low current design permits operation with typical standby and active currents of only 500nA (2μA maximum) and 320μA (400μA maximum) respectively.
Specifications:
Operating Temperature Min: -40°C
No. of Pins: 16Pins
Product Range: Octal 12-Bit SAR ADCs
Operating Temperature Max: 85°C
Supply Voltage Min: 2.7V
Supply Voltage Max: 5.5V
ADC / DAC Case Style: DIP
Data Interface: Serial, SPI
Sampling Rate: 100kSPS
Supply Voltage Type: Single
Resolution (Bits): 12bit
Input Channel Type: Pseudo Differential, Single EndedSKU: n/a -
Basic Electronic Components
MIC2288YD5-TR-MICROCHIP-DC-DC Switching Boost (Step Up) Regulator, Adjustable, 2.5V-10Vin, 3.6V-34Vout, 1Aout, SOT-23-5
-61%
Basic Electronic ComponentsMIC2288YD5-TR-MICROCHIP-DC-DC Switching Boost (Step Up) Regulator, Adjustable, 2.5V-10Vin, 3.6V-34Vout, 1Aout, SOT-23-5
The MIC2288YD5 TR is a 1A 1.2MHz PWM Boost Converter in low-profile. It implements a constant frequency, current mode control scheme with internal compensation that offers excellent transient response and output regulation performance. The high frequency operation saves board space by allowing small and external components. The fixed frequency PWM topology also reduces spurious switching noise and ripple to the input power source.
Features:
- Stable with ceramic capacitors
- High efficiency
- low input and output ripple
- Output over voltage protection
- Over-temperature shutdown
- -40 to 125°C Junction temperature range
SKU: n/a -
Basic Electronic Components
MCP3202-BI/P 12-Bit Dual Channel A/D Converter (ADC) with SPI Interface IC DIP-8 Package
-60%
Basic Electronic ComponentsMCP3202-BI/P 12-Bit Dual Channel A/D Converter (ADC) with SPI Interface IC DIP-8 Package
The MCP3202-BI/P 12-Bit P is a 12-bit analog-to-digital converter (ADC) with SPI serial interface and on-board sample-and-hold circuitry. It is designed for applications such as sensor interface, process control, and data acquisition, especially in battery-operated systems. The MCP3202-BI/P 12-Bit offers programmable analog inputs, allowing for either single-ended or pseudo-differential pairs. It operates over a wide voltage range and offers a low-power design for efficient performance.
Features :
- Single-ended or pseudo-differential inputs
- On-chip sample-and-hold
- Low power consumption: Standby current 0.5µA
- Operating voltage range: 2.7V to 5.5V
- Throughput rate: Up to 100 ksps
- Gain error: ±1.25 LSB (typical)
- Operating temperature: -40°C to +85°C
SKU: n/a -
Basic Electronic Components
MCP3421A0T-E/CH – 18-Bit Analog-to-Digital Converter I2C Interface On-Board Reference 6pin SOT-23 Microchip Technology
-51%
Basic Electronic ComponentsMCP3421A0T-E/CH – 18-Bit Analog-to-Digital Converter I2C Interface On-Board Reference 6pin SOT-23 Microchip Technology
the Microchip Technology MCP3421A0T ADC in an SOT-23 package is an 18-bit analog-to-digital converter designed for low-power applications. With a single channel and 3.75 S/s sampling rate, this device operates with a reference voltage of 2.048 V and supports I2C/serial/2-wire interfaces. It operates within a 2.7V to 5.5V supply range, consumes only 155 µA of current, and has an operating temperature range from -40°C to 125°C.
Features :
Resolution: 18 bits
Channels: 1
Interface: I2C, Serial, 2-Wire
Supply Voltage: 2.7V to 5.5V
Reference Voltage: 2.048V
Power Consumption: 155 µA
Sampling Rate: 3.75 S/s
Operating Temp Range: -40°C to 125°CSKU: n/a -
Basic Electronic Components
TC7660SCOA-MICROCHIP-DC/DC Inductorless Adjustable Inverter, 1.5 V to 12 V in, -12 V to -1.5 V/20 mA out, SOIC-8
-46%
Basic Electronic ComponentsTC7660SCOA-MICROCHIP-DC/DC Inductorless Adjustable Inverter, 1.5 V to 12 V in, -12 V to -1.5 V/20 mA out, SOIC-8
The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size, and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors.
The onboard oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+. Operation below 10 kHz (for lower supply current applications) is possible by connecting an external capacitor from OSC to the ground (with pin 1 open). The TC7660S is available in 8-pin PDIP and 8-pin Small Outline (SOIC) packages in commercial and extended temperature ranges.Applications:
- RS-232 Negative Power Supply
- Simple Conversion of +5V to ±5V Supplies
- Voltage Multiplication VOUT = ± n V+
- Negative Supplies for Data Acquisition Systems
and Instrumentation
SKU: n/a -
Basic Electronic Components
MAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package
-62%
Basic Electronic ComponentsMAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package
The MAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package is a compact, low-power device designed for digital signal processing. It operates with a 3 V to 3.6 V supply voltage and consumes a low operating current of 900 µA at 3.3 V. With a 14-bit resolution, this device is ideal for applications requiring precise data conversion. It features a digital output type and is housed in an 8-pin SO package. The device operates across a wide temperature range of -40°C to 125°C
Features :
- Interface: SPI
- Resolution: 14 bits
- Operating Voltage: 3 V to 3.6 V
- Operating Current: 900 µA
- Max Operating Temperature: 125°C
SKU: n/a -
Basic Electronic Components
ADS1110A0IDBVT-TEXAS INSTRUMENTS-Analogue to Digital Converter, 16 bit, 240 SPS, Differential, Single Ended, I2C, Single, 2.7 V
-49%
Basic Electronic ComponentsADS1110A0IDBVT-TEXAS INSTRUMENTS-Analogue to Digital Converter, 16 bit, 240 SPS, Differential, Single Ended, I2C, Single, 2.7 V
Features:
- 2.048V ±0.05% Accuracy
- 5ppm/°C Drift
- Onboard PGA
- Onboard oscillator
- 16-bits No missing codes
- 0.01% FSR Maximum INL
- Continuous self-calibration
- Single-cycle conversion
- 15 to 240SPS Programmable data rate
- I²C Interface, 8 available addresses
- 240µA Low current consumption
- No. of Pins: 6Pins
- Operating Temperature Min: -40°C
- Operating Temperature Max: 85°C
- Product Range: Single 16-Bit Sigma-Delta ADC
SKU: n/a -
Basic Electronic Components
MCP3201-CI/P 12-Bit A/D Converter (ADC) with SPI Interface IC DIP-8 Package
-62%
Basic Electronic ComponentsMCP3201-CI/P 12-Bit A/D Converter (ADC) with SPI Interface IC DIP-8 Package
The MCP3201-CI/P 12-Bit A/D Converter analog-to-digital converter (ADC) designed for precision measurement applications. Featuring an on-board sample and hold circuit, it allows for accurate conversions from a single-ended input. This ADC supports SPI communication for easy integration with microcontrollers, providing a sampling rate of up to 100 ksps at a clock rate of 1.6 MHz. With a wide operating voltage range of 2.7V to 5.5V, it ensures flexibility for various power supply setups. The device is optimized for low power, consuming only 500nA in standby mode and 300μA during active conversion, making it ideal for battery-powered and low-energy applications
Features :
12-bit Resolution: Provides high accuracy in analog-to-digital conversions.
On-chip Sample and Hold: Captures and holds the input signal for accurate conversions.
Single-Ended Input: Supports single-ended analog inputs for flexibility.
SPI Communication: Easy integration with microcontrollers via SPI interface.
Sampling Rate: Up to 100 ksps at 1.6 MHz clockSKU: n/a -
Basic Electronic Components
MCP4802-E/P 8 Bit Dual Voltage Digital to Analog Converter (DAC) with SPI Interface IC DIP-8 Package
-61%
Basic Electronic ComponentsMCP4802-E/P 8 Bit Dual Voltage Digital to Analog Converter (DAC) with SPI Interface IC DIP-8 Package
The MCP4802 device is dual 8-bit, 10-bit and 12-bit buffered voltage output Digital-to-Analog Converters (DACs), respectively. The devices operate from a single 2.7V to 5.5V supply with SPI-compatible Serial Peripheral Interface.
The device has a high precision internal voltage reference (VREF = 2.048V). The user can configure the full-scale range of the device to be 2.048V or 4.096V by setting the Gain Selection Option bit (gain of 1 of 2). Each DAC channel can be operated in Active or Shutdown mode individually by setting the Configuration register bits. In Shutdown mode, most of the internal circuits in the shutdown channel are turned off for power savings, and the output amplifier is configured to present a known high resistance output load. The devices include double-buffered registers, allowing synchronous updates of two DAC outputs using the LDAC pin. These devices also incorporate a Power-on Reset (POR) circuit to ensure reliable powerup. The devices utilize a resistive string architecture, with its inherent advantages of low DNL error, low ratiometric temperature coefficient, and fast settling time. These devices are specified over the extended temperature range (+125°C).
The device provides high accuracy and low noise performance for consumer and industrial applications where calibration or compensation of signals (such as temperature, pressure, and humidity) are required. The MCP4802/4812/4822 devices are available in the PDIP, SOIC, and MSOP packages.
Application:
- SetPoint or Offset Trimming
- Sensor Calibration
- Precision Selectable Voltage Reference
- Portable Instrumentation (Battery-Powered)
- Calibration of Optical Communication Devices
SKU: n/a -
Basic Electronic Components
MT8870 IC – DTMF Decoder IC
The MT8870 IC – DTMF Decoder is a high-performance DTMF receiver IC that can decode Dual-Tone Multi-Frequency signals into a 4-bit binary code. This IC is widely used in telephone dialing systems, automated phone systems, and remote control applications where DTMF signaling is employed. The SMD SOIC-18 package provides a compact and surface-mountable form factor ideal for modern electronic designs.
Features :
- DTMF Signal Decoding: Decodes 16 DTMF tones into a 4-bit binary output.
- High Noise Immunity: Offers reliable performance in noisy environments.
- Integrated Filters: Includes internal bandpass filters for signal conditioning.
- Power-On Reset: Ensures reliable initialization upon power-up.
- Low Power Consumption: Designed for low power operation.
- Programmable Tone Duration: Can be configured for different time intervals.
SKU: n/a -
Basic Electronic Components
TXB0104D Voltage Level Translator Bidirectional, 0.02 mA ns 100 Mbps
-53%
Basic Electronic ComponentsTXB0104D Voltage Level Translator Bidirectional, 0.02 mA ns 100 Mbps
This TXB0104D 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.2-V, 1.5- V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. VCCA must not exceed VCCB. When the OE input is low, all outputs are placed in the high-impedance state. To ensure the high-impedance state during power up or power down, OE must be tied to GND through a pulldown resistor The current sourcing capability of the driver determines the minimum value of the resistor. The TXB0104D device is designed so the OE input circuit is supplied by VCCA. This device is fully specified for partial power- down applications using I OFF. The I OFF circuitry disables the outputs, which prevents damaging current back-flow through the device when the device
is powered down.SKU: n/a -
Basic Electronic Components
MCP4922 12-Bit Dual Voltage Digital to Analog Converter (DAC) with SPI Interface IC DIP-14 Package
-59%
Basic Electronic ComponentsMCP4922 12-Bit Dual Voltage Digital to Analog Converter (DAC) with SPI Interface IC DIP-14 Package
The MCP4922-E/P is a 12-bit, dual-channel Digital-to-Analog Converter (DAC) with an external voltage reference. It features low power consumption (350µA typical), high accuracy (INL ±2 LSB, DNL ±0.75 LSB), and low noise performance. The device uses an SPI interface for communication and offers rail-to-rail output. Key features include a 4.5µs output settling time, simultaneous latching of both DACs via the LDAC pin, selectable unity or 2x gain output, and external multiplier mode, making it ideal for applications like set point control, offset adjustment, and sensor calibration.
Features :
- Resolution: 12-bit
- Data Interface: 3-wire, Serial
- Case Style: DIP (Dual In-line Package)
- Input Channel Type: Serial
- Operating Temperature: -40°C to 125°C
- Supply Voltage Range: 2.7V to 5.5V
- Number of Pins: 14 Pins
SKU: n/a -
Basic Electronic Components
ADS1115IDGSR-Texas Instruments-16-Bit 2V~5.5V 860Hz I2C VSSOP-10 Analog to Digital Converters (ADC) ROHS
-46%
Basic Electronic ComponentsADS1115IDGSR-Texas Instruments-16-Bit 2V~5.5V 860Hz I2C VSSOP-10 Analog to Digital Converters (ADC) ROHS
Manufacturer: Texas Instruments
Package: VSSOP-10
Resolution(Bits): 16-Bit
Voltage – Supply: 2V~5.5V
number of channels: 4
Operating Temperature: -40℃~+125℃
Sampling Rate: 860Hz
Integral non – linearity: 1LSB
Interface: I2C
differential input: YesSKU: n/a -
Basic Electronic Components
MCP3208 12-Bit 8-Channel A/D Converter (ADC) with SPI Interface IC DIP-16 Package
-62%
Basic Electronic ComponentsMCP3208 12-Bit 8-Channel A/D Converter (ADC) with SPI Interface IC DIP-16 Package
The MCP3208 12-Bit 8-Channel is a 12-bit ADC with SPI interface and 8 channels for analog inputs. It features a sampling rate of 100 ksps, and operates with a supply voltage range of 2.7V to 5.5V. This ADC offers a resolution of 12 bits, with integral nonlinearity (INL) of 1 LSB, and provides an output voltage of 4.1V. MCP3208 12-Bit 8-Channel A is ideal for applications requiring high-resolution, low-power signal conversion.
Features :
- 12-bit resolution
- 8 analog input channels
- Sampling rate: 100 ksps
- SPI interface
- Operating voltage: 2.7V to 5.5V
- Temperature range: -40°C to +85°C
SKU: n/a -
Basic Electronic Components
MCP3425A0T-E/CH-MICROCHIP-MCP3425A0T-E/CH-Analogue to Digital Converter, 16 bit, 15 SPS, Differential, I2C, Single, 2.7 V
-40%
Basic Electronic ComponentsMCP3425A0T-E/CH-MICROCHIP-MCP3425A0T-E/CH-Analogue to Digital Converter, 16 bit, 15 SPS, Differential, I2C, Single, 2.7 V
MCP3425 is a single channel low-noise, high accuracy ΔΣ A/D converter with differential inputs. Typical applications include portable instrumentation , weigh scales and fuel gauges, temperature sensing with RTD, thermistor and thermocouple, bridge sensing for pressure, strain and force.
Specifications:
Operating Temperature Min: -40°C
No. of Pins: 6Pins
Product Range: Single 16-Bit Sigma-Delta ADCs
Operating Temperature Max: 125°C
Supply Voltage Min: 2.7V
Supply Voltage Max: 5.5V
ADC / DAC Case Style: SOT-23
Data Interface: I2C
Sampling Rate: 15SPS
Supply Voltage Type: Single
Resolution (Bits): 16bit
Input Channel Type: DifferentialSKU: n/a -
Basic Electronic Components
MCP41100-I/SN-MICROCHIP-Volatile Digital Potentiometer, 100 kohm, Single, Serial, SPI, Linear, 2.7 V
-60%
Basic Electronic ComponentsMCP41100-I/SN-MICROCHIP-Volatile Digital Potentiometer, 100 kohm, Single, Serial, SPI, Linear, 2.7 V
MCP41100-I/SN is a single digital potentiometer with SPI™ interface. The wiper position of varies linearly and is controlled via an industry-standard SPI interface. The devices consume 1µA during static operation. A software shutdown feature is provided that disconnects the “A” terminal from the resistor stack and simultaneously connects the wiper to the “B” terminal. The wiper is reset to the mid-scale position (80h) upon power-up. The RS (reset, active low) pin implements a hardware reset and also returns the wiper to mid-scale.
Features:
- 256 taps for each potentiometer
- Potentiometer values for 10 kΩ, 50 kΩ and
100 kΩ - Single and dual versions
- SPI™ serial interface (mode 0,0 and 1,1)
- ±1 LSB max INL & DNL
- Low-power CMOS technology
- 1 µA maximum supply current in static operation
- Multiple devices can be daisy-chained together
(MCP42XXX only) - The shutdown feature opens circuits of all resistors for
maximum power savings - Hardware shutdown pin available on MCP42XXX
only
SKU: n/a -
Basic Electronic Components
VIPER22ADIP-E-STMICROELECTRONICS-VIPER22ADIP-E-AC/DC Off-Line Switcher IC, VIPerPlus Family, 195 VAC – 265 VAC, 60 kHz, 20 W, DIP-8
-49%
Basic Electronic ComponentsVIPER22ADIP-E-STMICROELECTRONICS-VIPER22ADIP-E-AC/DC Off-Line Switcher IC, VIPerPlus Family, 195 VAC – 265 VAC, 60 kHz, 20 W, DIP-8
The VIPER22ADIP-E is a fixed frequency off line converter in 8 pin DIP package. This off line converter combines dedicated current mode PWM controller with high voltage power MOSFET on same silicon chip. The internal control circuit offers large input voltage range on VDD pin which accommodates changes in auxiliary supply voltage. This feature is well adapted to battery charger adapter configurations.
Specifications:
IC Case / Package: DIP
Operating Temperature Min: -40°C
No. of Pins: 8Pins
Product Range: Multicomp Pro RJ45 Adapter
IC Mounting: Through Hole
Operating Temperature Max: 150°C
Input Voltage Max: 265VAC
Input Voltage Min: 195VAC
Power Rating Max: 20W
Power Switch Current Rating: 100µA
Switching Frequency: 60kHz
Power Switch Voltage Rating: 730VSKU: n/a -
Basic Electronic Components
ADS1247IPWR – 5.25V 24-Bit 2kSPS 4-Ch Delta-Sigma With PGA ADC IC SMD-20 Package
-57%
Basic Electronic ComponentsADS1247IPWR – 5.25V 24-Bit 2kSPS 4-Ch Delta-Sigma With PGA ADC IC SMD-20 Package
The ADS1247IPWR 24-bit ADC, in a 20-pin TSSOP package, offers a conversion rate of 2 ksps and a resolution of 24 bits. It operates with dual supply voltages between 2.7V and 5.25V, with a maximum power dissipation of 2.3 mW. Featuring 4 analog inputs and a bipolar polarity, the ADC supports SPI interface for communication. With a temperature range from -40°C to 105°C, it is RoHS compliant and consumes low power, making it suitable for various analog-to-digital conversion applications.
Features :
- Resolution: 24-bit ADC with high precision.
- Sampling Rate: 2 ksps (kilosamples per second).
- Dual Supply Voltage: Operates between 2.7V to 5.25V.
- Power Consumption: Low power dissipation of 2.3 mW.
- Temperature Range: Works in temperatures from -40°C to 105°C
SKU: n/a -
Basic Electronic Components
ADS1232 24Bit Low Noise AD Analog To Digital Converter Module
The ADS1232/4 is a high-precision 24-bit Analog-to-Digital Converter (ADC), designed specifically for use with bridge sensors such as load cells, strain gauges, and pressure sensors. With an integrated low-noise programmable gain amplifier (PGA), a delta-sigma ADC with exceptional noise performance, and an onboard temperature sensor (ADS1232), the ADS1232/4 offers a complete solution for accurate and reliable sensor measurement.
Features:
- 24-bit resolution with up to 23.5 effective bits of accuracy for precise measurements.
- Low-noise programmable gain amplifier (PGA) with selectable gains of 1, 2, 64, and 128.
- RMS noise of 17nV at 10SPS and 44nV at 80SPS for clean data.
- Over 100 dB of 50Hz and 60Hz noise rejection for stable measurements in noisy environments.
- Built-in temperature sensor (ADS1232) for temperature monitoring.
- Flexible clocking options with a low-drift onboard oscillator (±3%) and optional external crystal.
- Easy ratiometric measurements with an external voltage reference up to 5V.
- Selectable data rates of 10SPS or 80SPS for different sampling needs.
- Two-channel differential input (ADS1232) or four-channel differential input (ADS1234).
- SPI interface for simple and reliable serial data transfer.
- Wide supply range of 2.7V to 5.3V for flexible system integration.
- Operating temperature range of -40°C to +105°C for industrial-grade reliability.
SKU: n/a -
Basic Electronic Components
TNY280PN Power Integrations AC/DC Converter IC DIP-8 Package
The TNY280PN is a high-efficiency AC/DC Converter IC from Power Integrations, designed for compact and energy-efficient power supply solutions. It features Tiny Switch-III technology, integrating a high-voltage power MOSFET, oscillator, and control logic into a DIP-8 package, reducing component count and simplifying circuit design.
Features:
- Integrated High-Voltage Power MOSFET: Reduces external components and simplifies circuit design.
- Wide Input Voltage Range: Supports 85V to 265V AC, making it ideal for universal power applications.
- TinySwitch-III Technology: Enhances energy efficiency, reduces switching losses, and improves thermal performance.
- High Efficiency: Lowers power dissipation, minimizing heat generation.
- Ultra-Low Standby Power Consumption: Meets modern energy-saving standards with minimal power draw in standby mode.
SKU: n/a -
Basic Electronic Components
ADC0808CCN PDIP-28 Analog to Digital Converter-ADC
The ADC0808CCN PDIP-28 Analog to Digital Converter-ADC is a µP compatible Analog-to-digital Converter (ADC) with 8-channel multiplexer. The 8-bit A/D converter uses a successive approximation as the conversion technique. The converter features a high impedance chopper stabilized comparator, a 256R voltage divider with analog switch tree and a successive approximation register.The 8-channel multiplexer can directly access any of 8-single-ended analog signals. The device eliminates the need for external zero and full-scale adjustments. Easy interfacing to microprocessors is provided by the latched and decoded multiplexer address inputs and latched TTL TRI-STATE outputs.The design of the ADC0808 has been optimized by incorporating the most desirable aspects of several A/D conversion techniques. The ADC0808 offers high speed, high accuracy, minimal temperature dependence, excellent long-term accuracy and repeatability and consumes minimal power. These features make this device ideally suited to applications from a process.SKU: n/a -
Basic Electronic Components
LM386MX-1/NOPB 700-mW, mono, 5- to 18-V, analog input Class-AB audio amplifier IC SMD-8 Package
-58%
Basic Electronic ComponentsLM386MX-1/NOPB 700-mW, mono, 5- to 18-V, analog input Class-AB audio amplifier IC SMD-8 Package
The LM386M-1 and LM386MX-1 are power amplifiers designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 increases the gain to any value from 20 to 200.The inputs are ground referenced while the output automatically biases to one-half the supply voltage. The quiescent power drain is only 24 mW when operating from a 5V supply.
Features :
Battery Operation
Minimum External Parts
Wide Supply Voltage Range: 5 V–18 V
Low Quiescent Current Drain: 4 mA
Voltage Gains from 20 to 200
Ground-Referenced InputSKU: n/a -
Basic Electronic Components
TPS5430DDAR original IC SO-PowerPad-8 Step-Down Converter IC
The TPS5430DDAR is a high-output-current PWM converter that integrates a low-resistance, high-side N-channel MOSFET. Included on the substrate with the listed features are a high-performance voltage error amplifier that provides tight voltage regulation accuracy under transient conditions; an Undervoltage lockout circuit to prevent start-up until the input voltage reaches 5.5 V; an internally set slow-start circuit to limit inrush currents, and a voltage feedforward circuit to improve the transient response.
Using the ENA pin, the shutdown supply current is reduced to 18 μA typically. Other features include an active-high enable, overcurrent limiting, over-voltage protection, and thermal shutdown. To reduce design complexity and external component count, theTPS543x feedback loop is internally compensated. The TPS5431 is intended to operate from power rails up to 23 V. The TPS5430 regulates a wide variety of power sources including 24 V bus. The TPS543x device is available in a thermally enhanced, easy-to-use 8-pin SOIC PowerPAD package. TI provides evaluation modules and the
A designer software tool to aid in quickly achieving high-performance power supply designs to meet aggressive equipment development cycles.SKU: n/a -
Basic Electronic Components
MCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC DIP-16 Package
-53%
Basic Electronic ComponentsMCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC DIP-16 Package
The Microchip Technology Inc.MCP3008 8-Channel 10-Bit devices are successive approximation 10-bit Analogto-Digital (A/D) converters with on-board sample and hold circuitry. The MCP3008 is programmable to provide four pseudo-differential input pairs or eight single-ended inputs. Differential Non linearity (DNL) and Integral Non linearity (INL) are specified at ±1 LSB. Communication with the devices is accomplished using a simple serial interface compatible with the SPI protocol.
The devices are capable of conversion rates of up to 200 ksps. The MCP3008 8-Channel 10-Bit operate over a broad voltage range (2.7V – 5.5V). Low-current design permits operation with typical standby currents of only 5 nA and typical active currents of 320 µA. The MCP3008 is offered in 16- pin PDIP and SOIC packages.
Features:
- 10-bit resolution
- ± 1 LSB max DNL
- ± 1 LSB max INL
- 8 (MCP3008) input channels
- Analog inputs programmable as single-ended or pseudo-differential pairs
- On-chip sample and hold
- SPI serial interface (modes 0,0 and 1,1)
- Single supply operation: 2.7V – 5.5V
- 200 ksps max. sampling rate at VDD = 5V
- 75 ksps max. sampling rate at VDD = 2.7V
- Low power CMOS technology • 5 nA typical standby current, 2 µA max.
- 500 µA max. active current at 5V
- Industrial temp range: -40°C to +85°C
SKU: n/a -
Basic Electronic Components
MCP4921 12 Bit Voltage Output Digital to Analog Converter (DAC) with SPI Interface IC DIP-8 Package
-34%
Basic Electronic ComponentsMCP4921 12 Bit Voltage Output Digital to Analog Converter (DAC) with SPI Interface IC DIP-8 Package
The MCP4921 is a 12-bit Digital-to-Analog Converter (DAC) from Microchip Technology, featuring a voltage output and SPI interface. It supports both unipolar and bipolar output polarities and has a settling time of 4.5 μs. The device operates with a supply voltage of 2.7V to 5.5V and provides low power consumption with a nominal current of 175 μA. It has a maximum operating temperature of 125°C and comes in a lead-free PDIP-8 package, ideal for various industrial applications.
Features :
- Resolution: 12-bit
- Output Type: Voltage output (unipolar/bipolar)
- Interface: SPI (Serial Peripheral Interface)
- Settling Time: 4.5 μs
- Supply Voltage: 2.7V to 5.5V
- Nominal Supply Current: 175 μA
- Operating Temperature Range: -40°C to 125°C
SKU: n/a -
Basic Electronic Components
ADC0804LCN PDIP-20 Analog to Digital Converter-ADC
Features:
- Supply voltage range from 4.5V to 6.3V
- Sampling rate is 9.708KSPS
- Compatible with 8080 microprocessor derivatives, no interfacing logic needed
- Differential analogue voltage inputs
- Logic inputs and outputs meet both MOS and TTL voltage level specifications
- Works with 2.5V (LM336) voltage reference
- On-chip clock generator
- Operating temperature range -40°C to 85°C
- No zero adjust required
- Easy interface to all microprocessors and operates as a standalone device
- Applications: Signal Processing
SKU: n/a
Skip to navigation
Skip to content
