Electronic Components
Showing 817–840 of 1177 results
-
-
Basic Electronic Components
LM8UU 8 MM Linear Motion Bearing
The LM8UU 8 MM Linear Motion Bearing is a device that provides precise, safe and reliable linear motion along a single axis. It is commonly used in 3D printers and CNC (Computer Numerical Control) machines, as well as in DIY and robotics prototyping projects.
The LM8UU 8 MM Linear Motion Bearing consists of a high-carbon chromium steel case, a synthetic resin retainer plate and a set of balls that run along a smooth ball guide surface. The case has an 8mm bore and a 15mm outer diameter, and it can be mounted on a slide unit to support other components. The retainer plate ensures accurate ball guidance and low noise, even at high speeds. The balls reduce friction and increase efficiency and energy saving.
The LM8UU 8 MM Linear Motion Bearing is designed with standardized and interchangeable parts, so replacing any worn parts is easy and convenient. To maintain the optimal performance of the linear motion bearing, the shaft that it slides along should be lubricated regularly. The quality of the shaft also affects the quality of the linear motion, so using a chrome plated and hardened shaft is recommended.
Features :
- Outer Casing: Chromium Steel
- Low friction, optimum loading capacity, long life.
- It has linear bearing ball cage, hardened coat at both end rings.
- No worry if replacement of any worn part.
- Low noise even in high-speed operation.
SKU: n/a -
Basic Electronic Components, Electronic Components, IoT and Wireless
LoRa Ra-02 SX1278 433MHz Wireless Spread Spectrum Transmission Module
-48%
Basic Electronic Components, Electronic Components, IoT and WirelessLoRa Ra-02 SX1278 433MHz Wireless Spread Spectrum Transmission Module
- Module Model: LoRa-RA-02, Input Supply Range: 2.5 ~ 3.7VDC, Interface: SPI, Programmable bit Rate: UP to 300Kbps
- Antenna Type: IPEX, Frequency Range: 410-525 MHz, Transmit Power: 18±1 dBm (Max), Operating Temperature: -10 to 85°C, LoRa Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change, High sensitivity: down to -148dBm, Half-duplex SPI communication, Programmable bit rates up to 300kbps, Supports FSK, GFSK, MSK, GMSK, LoRa, and OOK modulation modes
- 127dB RSSI dynamic range, Automatic RF signal detection, CAD model, and very high-speed AFC, Packet engine with CRC up to 256 bytes, Small footprint dual-row stamp-hole patch package; Dimension: Length-28mm, Width-20mm, Height-5mm, Weight-7gm
SKU: n/a -
Basic Electronic Components
LT-633(SPL-63) Stationary, Type Quick Connection, Terminal
LT-633(SPL-63) Stationary, Type Quick Connection, Terminal
It can be used to create the two-wire connection from two pair connections as shown in below Picture
PCT Spring Lever Connector contains a compact locking wire connector by a spring lever, which is used for single-strand hardwire with 0.08mm to 2.5mm2 area or soft wire with 0.08mm to 4.0mm2 area (or AWG28 to AWG12). This connector can tolerate the rated voltage up to 600V with an electric current peak of 32A, resulting in a maximum of 7KW Power. And the Stripping Length of the connector is 11-12 mm
SKU: n/a -
Basic Electronic Components
luminum GT2 Timing Pulley 20 Tooth 8mm Bore For 6mm Belt
This is Aluminum GT2 Timing Pulley 20 Tooth 6.35mm Bore For 6mm Belt. For precise motion control, GT2 belts and pulleys offer excellent precision at a great price. This pulley is meant for use with GT2 6mm wide belts only – MXL belts will slip due to the different tooth profiles.
This pulley has 20 teeth and a 6.35mm inner bore. Two set screws can be used to attach it firmly to any 6.35mm diameter shaft. Full aluminum construction means these are very light and very durable.
SKU: n/a -
Basic Electronic Components
M3*30MM Male to Female Nylon Hex Spacer-(Pack of 10)
M3*30MM Male to Female Nylon Hex Spacer-(Pack of 10)
Elevate and securely mount your PCB with our M3*30MM Male to Female Nylon Hex Spacer (Pack of 10). These versatile standoffs are designed to provide a stable mounting solution for your PCB while offering ample space for airflow, making them perfect for a variety of applications including inside computer chassis, Quadcopter frames, Motor Driver Bodies, and DIY projects.
Crafted from high-quality brass, our nylon spacers boast anti-corrosion and anti-rust properties, ensuring durability and longevity. Their threaded hexagonal column design makes installation a breeze, allowing for easy segregation of boards.
Features:
- Excellent strength and durability
- Fine finish for a professional look
- Sturdy construction for reliable performance
- Versatile design for a wide range of applications
- Securely locks PCB into place
- Hexagonal design allows for easy tightening with a wrench
Enhance the stability and airflow of your projects with our M3*30MM Male to Female Nylon Hex Spacer (Pack of 10). Please note that the product images may vary slightly from the actual product in terms of color tone.
SKU: n/a -
Basic Electronic Components
M6 Pneumatic Push in Bowden Extruders with 4*2mm Tube
he PC4-M6 Pneumatic Push-in Bowden Extruder for 4mm J-Head fitting is an essential component for 3D printers using 1.75mm filament in Bowden-style extruder assemblies. It connects PTFE tubing to the extruder, allowing for a smooth and reliable path for the filament to reach the hot-end assembly. This connector is compatible with standard 4mm ID PTFE tubing and features a universal M6 thread that fits most extruder fittings. By ensuring that the filament travels safely and efficiently, this connector improves print quality and consistency.
The PC4-M6 Bowden connector uses a John Guest fitting, which secures the tubing with tension, ensuring a firm grip and minimizing the risk of any disruptions in filament flow. Its high corrosion resistance and compatibility make it a popular choice for Bowden-style extruders, contributing to longer-lasting, reliable 3D printing.
SKU: n/a -
Basic Electronic Components
M6 Thread Brass Nozzle V5 V6 UM Compatible – 1.75mm x 0.4mm (for 3D printer)
-57%
Basic Electronic ComponentsM6 Thread Brass Nozzle V5 V6 UM Compatible – 1.75mm x 0.4mm (for 3D printer)
This 3D Printers Brass Nozzle 0.4mm is a fully functional metal extruder, backwards compatible with all 3d printer is basically a high-end dual extrusion system, using two interchangeable nozzles.
You can use two different wires in the same print job and be able to do their own level, and regardless of which side printing heat will not appear other double extruder 3D printer rubs and other common problems.
SKU: n/a -
Basic Electronic Components
M6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.4mm (for 3D printer)
-35%
Basic Electronic ComponentsM6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.4mm (for 3D printer)
M6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.4mm (for 3D printer)
Whether you want to print fine details or large parts, you can find the right V6 M6 Thread Brass Nozzle for your 3D printer at robu.in. These nozzles are part of the V6 ecosystem of 3D printer parts and work with V6, Lite6, and Titan Aero. They also fit Prusa 3D printers.
These nozzles have an optimized internal geometry that reduces back-pressure and allows a smooth and easy flow of filament. They also enhance the retraction performance.
The tip of the nozzle has a flat surface that flattens the layer as it prints. The size of the tip is customized for each nozzle size. A small tip gives you high precision and a large tip helps you print smoother larger layers.
You can easily identify each nozzle in the series by the markings on the hex head flats. See the table on the left for reference.
SKU: n/a -
Basic Electronic Components
M6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.6mm (for 3D printer)
-51%
Basic Electronic ComponentsM6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.6mm (for 3D printer)
If you want to print fine details or large parts with your 3D printer, you can use the V6 M6 Thread Brass Nozzle range from robu.in. These nozzles are compatible with V6, Lite6, and Titan Aero 3D printer parts. You can also use them with Prusa 3D printers.
These nozzles have a M6 thread and fit any 3D printers that use the V6 ecosystem, including Prusa i3 and i3 MK2 models. They have an optimized internal geometry that reduces back-pressure and allows a smooth and easy flow of filament. They also improve the retraction performance.
The tip of the nozzle has a flat surface that flattens the layer as it prints. The size of the tip is custom machined for each nozzle size. A small tip gives you high precision and a wide tip helps you print larger layers smoothly.
You can easily identify each nozzle in the series by the markings on the hex head flats. See the table on the left for reference.
SKU: n/a -
Basic Electronic Components
MACH3 V2.0 Engraving Machine Motherboard CNC 5- Axis+USB Cable+CD
If you’re tired of needing a parallel port and an outdated PC to run Mach3, this is the solution you’ve been waiting for! Our newest interface board runs through any standard USB port for communication. You simply need to install the card’s plugin for Mach3 and follow the setup instructions.
This Mach3 USB Controller will run Mach3 through a standard USB port on a PC. You can use Windows 10 and older Windows version 32-bit or 64-bit.
Features:
- External wide voltage input, 12-24V, and anti-reverse function.
- Support various versions of MACH3 software and support the latest version.
- Support Windows XP, WIN7, WIN8, WIN10, support for 64-bit systems, support laptops, support for tablet computers.
- All input signals are separated by light, and emergency stop, knife set, limit, and zero return can be connected to ensure computer security. The input can be connected to a mechanical switch or a proximity switch (normally open with NPN).
- All the way through the optocoupler isolated 0-10V analogue voltage output, you can control the 0-10V analogue voltage input inverter, control the spindle speed.
- Provide PWM output (5V level), which can be connected to the spindle speed controller controlled by PWM.
- Provide 4 output ports (5V level), can be connected with the optocoupler relay module, control water cooling, spray and so on.
- Maximum 100KHZ output per axis can be connected to the common anode or common cathode, the input level is 5V, stepper or servo motor driver with optocoupler input (pulse direction).
- At the same time provide a 5-axis interface cable socket (XH2.54), easy to connect
SKU: n/a -
Basic Electronic Components
Male + Female 2.1*5.5mm for DC Power Jack Adapter Connector Plug For CCTV Camera
-39%
Basic Electronic ComponentsMale + Female 2.1*5.5mm for DC Power Jack Adapter Connector Plug For CCTV Camera
This is Male + Female 2.1*5.5mm for DC Power Jack Adapter Connector Plug For CCTV Camera. Simple & Professional appearance for power cabling.
Easier for camera installation saves time and assures secure cable connection. No electrical tap, No splicing, no crimping, but only a small screwdriver.
Features:
- It is a perfect solution for those who want to make custom power cable.
- This CCTV Camera DC Power Connector will provide a great connection.
Female Jack Description:
- 5.5mm x 2.1mm Female power plug connector.
- The external diameter of the plug: 5.5mm.
- The internal diameter of the plug: 2.1mm.
- Dimension: 38mm(L) x 14mm(W) x 13mm(H).
Male jack Description:
- 2.1 x 5.5mm CCTV Camera DC Power Plug Connector.
- DC Power Plug with plastic construction and strain relief.
- This 2.1 x 5.5mm Power Plug features one power connector end DC plug male to another end terminal for CCTV camera connected.
- The internal diameter of the plug: 2.1mm
- The external diameter of the plug: 5.5mm
SKU: n/a -
Basic Electronic Components
Male to Male Jumper Wires 40 Pin 30cm
This is male to male Dupont/Jumper Wire 40 Pin 30cm. A very Flexible and easily detachable cable to the no. of wires according to your requirement. It has 1Pin male to the 1pin male header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers.
This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering.
Individual Dupont Cables are fitted by inserting their “end connectors” into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment.
Mostly it is useful with Orange Pi, Banana Pi, Raspberry Pi, Arduino, and other mini pc and development board. It is very useful in the PCB project, pc motherboard, as well as Breadboard connections. Additionally, it allows you to plug and unplug easily for prototyping and can be used over and over again.
SKU: n/a -
Basic Electronic Components
MAX232 Dual Driver/Receiver IC DIP-16 Package
MAX232 Dual Driver/Receiver IC DIP
The MAX232E belongs to a family of transceivers that can operate with a single +5V supply and have high ±15kV ESD HBM protection. They can communicate using RS-232 and V.28 protocols. The Selector Guide shows the different features of each device in this family. The drivers and receivers of all these devices comply with the EIA/TIA232E and CCITT V.28 standards and can support data rates up to 120kbps when loaded. The MAX232E is available in 16-pin TSSOP, narrow SO, wide SO, and DIP packages.
Features
Saves Board Space
Integrated High ±15kV HBM ESD Protection
Integrated Charge Pump Circuitry-Eliminates the Need for a Bipolar ±12V Supply, Enables Single Supply Operation From +5V Supply.
SKU: n/a -
Basic Electronic Components
MAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package
-62%
Basic Electronic ComponentsMAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package
The MAX31855KASA+T – 1-Ch 14bits Thermocouple-to-Digital Converter SPI Remote Sensor IC SMD-8 Package is a compact, low-power device designed for digital signal processing. It operates with a 3 V to 3.6 V supply voltage and consumes a low operating current of 900 µA at 3.3 V. With a 14-bit resolution, this device is ideal for applications requiring precise data conversion. It features a digital output type and is housed in an 8-pin SO package. The device operates across a wide temperature range of -40°C to 125°C
Features :
- Interface: SPI
- Resolution: 14 bits
- Operating Voltage: 3 V to 3.6 V
- Operating Current: 900 µA
- Max Operating Temperature: 125°C
SKU: n/a -
Basic Electronic Components
MAX485 TTL to RS485 Converter Module
MAX485 TTL to RS485 Converter Module
The MAX485 TTL To RS485 Module is a device that transforms TTL signals into RS485 signals. RS485 is a standard for differential communication that allows high-speed data transmission over long distances and in noisy environments. RS485 networks can connect multiple receivers in a linear, multi-drop configuration, which makes them suitable for industrial and similar applications.
This converter enables your Arduino/microcontroller to send and receive data using the RS485 network. RS485 is similar to Serial TTL and RS232 interfaces, but with extra features. It can support data transfer between up to 32 devices on the same data line, over a cable length of up to 1.2km (4000ft), with a maximum data rate of 10Mbit/s. This converter is designed for office and industrial applications (non-isolated) and offers superior characteristics/features that are usually found only on more expensive units.
SKU: n/a -
Basic Electronic Components, Uncategorized
MAX6675 Module with K Type Thermocouple Sensor
MAX6675 Module with K Type Thermocouple Sensor
This module utilizes the Maxim MAX6675 IC to convert the input from a K-Type thermocouple sensor into a digital serial output, compatible with microcontrollers via SPI. It offers temperature measurements ranging from 0°C to 1024°C with 12-bit resolution and 0.25°C accuracy. The sensor included with the module can withstand temperatures up to 450°C.
For easy integration, the module features screw terminals for connecting the thermocouple’s spade connectors and a 5-pin 0.1″ header for microcontroller interfacing, such as with an Arduino board.
The included thermocouple sensor has a 4.5mm diameter with a 6mm threaded mounting bolt. The sensor’s cable and spade connectors are approximately 100cm in length, providing flexibility in placement.
Features of MAX6675 Module with K Type Thermocouple Sensor: –
This device has an internal circuit that compensates for the cold junction of the thermocouple.
It can convert the temperature signal into a 12-bit digital format.
It also has a built-in feature that detects if the thermocouple is broken.
It uses a K-type temperature probe and outputs the temperature through a simple SPI serial interface.
It has high impedance differential inputs and can withstand 2000V of ESD signal.SKU: n/a -
Electronic Components
MB102 830 Points Breadboard+Power Supply+140 Jumper Wires Kit
- Distribution strip, Tie-point 200
- Terminal Strip, Tie-point 630
- Completely reusable Breadboard
- Brand new & high quality
- Breadboard power supply module, compatible with 5 V, 3.3 V
- 140pcs Solderless Breadboard Jumper Cable Lead Kit
- Hard Wire with Angled shape
SKU: n/a -
Basic Electronic Components
MB102 830 Points Solderless Breadboard
MB102 830 Points Solderless Breadboard
The AMB102 830 Points Solderless Breadboard is an essential tool for experimenting with circuit designs in both R&D and university labs. It allows you to create temporary circuits for testing or to explore new ideas without the need for soldering, making it easy to change connections and replace components.
With 830 tie points—comprised of 128 groups of 5 connected terminals and 8 buses of 25 connected terminals—this breadboard is reusable, ensuring that components remain undamaged for future use. It accommodates various electronic components such as transistors, diodes, LEDs, resistors, and capacitors, allowing for quick prototyping of electronic circuits.
Designed to fit jumper wires with a diameter of 0.8mm and featuring standard 2.54mm hole spacing, the breadboard also has an adhesive sheet on the back for easy mounting. Multiple breadboards can be spliced together for larger projects, enhancing its versatility for your circuit-building needs.
SKU: n/a -
Basic Electronic Components, Electronic Components
MB102 830 Points Solderless Prototype PCB Breadboard
-22%
Basic Electronic Components, Electronic ComponentsMB102 830 Points Solderless Prototype PCB Breadboard
An MB102 830 Points Solderless Prototype PCB Breadboard is an invaluable tool for experimenting with circuit designs whether in the R&D or university lab. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components.
Features :
- Mb102 Bread Board
- 830 Solder-less Points
- Ideal for Experimenting With Circuit Design In Labs
- Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components
- Completely reusable
- Colored coordinates for easy components placement.
- Phosphor bronze nickel plated spring clips.
- Accept a variety of wire sizes 20-29 AWG
SKU: n/a -
Electronic Components
MB102 830 Points Solderless Prototype PCB Breadboard High Quality
- Mb102 Bread Board
- 830 Solder-less Points
- Ideal for Experimenting With Circuit Design In Labs
- Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components
- Colored coordinates for easy components placement.
- Accept a variety of wire sizes 20-29 AWG
SKU: n/a -
Basic Electronic Components
MCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC DIP-16 Package
-53%
Basic Electronic ComponentsMCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC DIP-16 Package
The Microchip Technology Inc.MCP3008 8-Channel 10-Bit devices are successive approximation 10-bit Analogto-Digital (A/D) converters with on-board sample and hold circuitry. The MCP3008 is programmable to provide four pseudo-differential input pairs or eight single-ended inputs. Differential Non linearity (DNL) and Integral Non linearity (INL) are specified at ±1 LSB. Communication with the devices is accomplished using a simple serial interface compatible with the SPI protocol.
The devices are capable of conversion rates of up to 200 ksps. The MCP3008 8-Channel 10-Bit operate over a broad voltage range (2.7V – 5.5V). Low-current design permits operation with typical standby currents of only 5 nA and typical active currents of 320 µA. The MCP3008 is offered in 16- pin PDIP and SOIC packages.
Features:
- 10-bit resolution
- ± 1 LSB max DNL
- ± 1 LSB max INL
- 8 (MCP3008) input channels
- Analog inputs programmable as single-ended or pseudo-differential pairs
- On-chip sample and hold
- SPI serial interface (modes 0,0 and 1,1)
- Single supply operation: 2.7V – 5.5V
- 200 ksps max. sampling rate at VDD = 5V
- 75 ksps max. sampling rate at VDD = 2.7V
- Low power CMOS technology • 5 nA typical standby current, 2 µA max.
- 500 µA max. active current at 5V
- Industrial temp range: -40°C to +85°C
SKU: n/a -
Basic Electronic Components
MCP3201-CI/P 12-Bit A/D Converter (ADC) with SPI Interface IC DIP-8 Package
-62%
Basic Electronic ComponentsMCP3201-CI/P 12-Bit A/D Converter (ADC) with SPI Interface IC DIP-8 Package
The MCP3201-CI/P 12-Bit A/D Converter analog-to-digital converter (ADC) designed for precision measurement applications. Featuring an on-board sample and hold circuit, it allows for accurate conversions from a single-ended input. This ADC supports SPI communication for easy integration with microcontrollers, providing a sampling rate of up to 100 ksps at a clock rate of 1.6 MHz. With a wide operating voltage range of 2.7V to 5.5V, it ensures flexibility for various power supply setups. The device is optimized for low power, consuming only 500nA in standby mode and 300μA during active conversion, making it ideal for battery-powered and low-energy applications
Features :
12-bit Resolution: Provides high accuracy in analog-to-digital conversions.
On-chip Sample and Hold: Captures and holds the input signal for accurate conversions.
Single-Ended Input: Supports single-ended analog inputs for flexibility.
SPI Communication: Easy integration with microcontrollers via SPI interface.
Sampling Rate: Up to 100 ksps at 1.6 MHz clockSKU: n/a -
Basic Electronic Components
MCP3202-BI/P 12-Bit Dual Channel A/D Converter (ADC) with SPI Interface IC DIP-8 Package
-60%
Basic Electronic ComponentsMCP3202-BI/P 12-Bit Dual Channel A/D Converter (ADC) with SPI Interface IC DIP-8 Package
The MCP3202-BI/P 12-Bit P is a 12-bit analog-to-digital converter (ADC) with SPI serial interface and on-board sample-and-hold circuitry. It is designed for applications such as sensor interface, process control, and data acquisition, especially in battery-operated systems. The MCP3202-BI/P 12-Bit offers programmable analog inputs, allowing for either single-ended or pseudo-differential pairs. It operates over a wide voltage range and offers a low-power design for efficient performance.
Features :
- Single-ended or pseudo-differential inputs
- On-chip sample-and-hold
- Low power consumption: Standby current 0.5µA
- Operating voltage range: 2.7V to 5.5V
- Throughput rate: Up to 100 ksps
- Gain error: ±1.25 LSB (typical)
- Operating temperature: -40°C to +85°C
SKU: n/a
