Sensors
Showing 577–600 of 995 results
-
Sensors
MQ-3 Alcohol Detector Gas Sensor Module
- Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off).
- Current Consumption: 150mA.
- DO output: 0.1 and 5V.
- AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detecting Concentration: 0.05-10mg/L Alcohol.
SKU: n/a -
Sensors
MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module
- Detecting range: 300~10000ppm
- Signal output indicator.
- Dual Signal output (analog output and TTL output).
- The TTL output signal is low level, allows us to connect with SCM directly.
- Analog output 0~5V voltage.
- Quick response and recovery.
SKU: n/a -
Sensors
MQ-7 CO Carbon Monoxide Coal Gas Sensor Module
- Operating voltage: DC 5 V.
- The analog output voltage, the higher the concentration the higher the voltage.
- The carbon monoxide detection with better sensitivity.
- With a long service life and reliable stability.
- Rapid response and recovery characteristics.
- Range: 10 to 1000 ppm.
SKU: n/a -
Sensors
MQ-8 Hydrogen Gas Sensor Module H2 Alarm Detection
- Using high-quality dual-panel design, with power indicator and TTL signal output instructions.
- The switching signal having a DO (TTL) output and analog output AO.
- TTL output valid signal is low.
- The higher the voltage, the concentration of the analog output voltage is higher.
- A hydrogen gas detection with good sensitivity.
- Has a long life and reliable stability
SKU: n/a -
-
-
-
-
Sensors
MULTICOMP PRO Ultrasonic Sensor, Transceiver, 16 mm Diameter, 40 kHz, -74 dB, Plastic, Black, -30 °C to 85 °C
-18%
SensorsMULTICOMP PRO Ultrasonic Sensor, Transceiver, 16 mm Diameter, 40 kHz, -74 dB, Plastic, Black, -30 °C to 85 °C
- Product: MULTICOMP PRO Ultrasonic Sensor, Transceiver
- Aftershock Time: max. 1.5ms
- Sensitivity Distance: 0.6m to 16m
- Capacitance: 3,000pF 20% at1kHz
- Less power consumption
- High reliability
- Plastic Housing Material
- Open struct Construction
SKU: n/a -
-
Sensors
Normally open vibration sensor module
- The working voltage of 3.3V-5V.
- Using the company’s high-sensitivity vibration switch, the default with SW-18015P vibration sensor.
- The comparator output, the signal clean, good waveform, driving ability, more than 15mA
- With a fixed bolt hole, easy to install.
- The use of wide voltage LM393 comparator.
SKU: n/a -
-
Sensors
NXP Daughter Board, Sensor Toolbox Shield Board, 3-axis Gyroscope, 6-axis Accelerometer/Magnetometer
-22%
SensorsNXP Daughter Board, Sensor Toolbox Shield Board, 3-axis Gyroscope, 6-axis Accelerometer/Magnetometer
- Product: NXP Daughter Board, Sensor Toolbox Shield Board, 3-axis Gyroscope, 6-axis Accelerometer/Magnetometer
- Silicon Core Number: FXAS21002, FXOS8700
- Silicon Manufacturer: NXP
- Accelerometer/Magnetometer: 6-axis
SKU: n/a -
Sensors
OE-775 Hall Effect Two Channel Magnetic Encoder(Color may vary )
This encoder is featured and developed for the series of Orange planetary DC gear motors. The encoder are tested for its precise output and robustness in all electronic as well as environmental parameters listed. So If you wish to add feedback to older or new gear motors this encoder will do the trick as long as your Motor has a long back shaft.
SKU: n/a
