- Adopts Precision Compensation Technology
- High Accuracy Sensor
- Suitable For Gas,Liquid,Oil
- Stainless Steel Body
1.0MPa Stainless Steel Pressure Transducer Sensor
20 in stock
- Adopts Precision Compensation Technology
- High Accuracy Sensor
- Suitable For Gas,Liquid,Oil
- Stainless Steel Body
₹1,700.00 ₹2,999.00
20 in stock
CompareBased on 0 reviews
Be the first to review “1.0MPa Stainless Steel Pressure Transducer Sensor” Cancel reply
Related products
-
Uncategorized, Basic Electronic Components, Electronic Components
12 x 18 cm Double-Side Universal PCB Prototype Board
-34%Uncategorized, Basic Electronic Components, Electronic Components12 x 18 cm Double-Side Universal PCB Prototype Board
0 out of 5(0)This is a Universal PCB Prototype Board Double-Side 12 x 18 CM High-quality universal prototyping board with standard 0.1″ spacing through holes.
High-quality 12 x 18Â CM FR4 material, Double-sided, HASL, NC CNC drilled.
Features:
- Dimension: 12 x 18Â CM
- Base Material: FR4
- Copper Thickness 1-4 OZ
- Board Thickness 1.6
- Min. Hole Size 0.3mm
- Min. Line Width 6mil
- Min. Line Spacing 6mil
- Surface Finishing HASL
Package Includes :
1 x Universal PCB Prototype Board Double-Side 12 x 18 CM
SKU: n/a -
Uncategorized
5V Single Channel RELAY Module
0 out of 5(0)This is a 5V single Channel Relay Board Module For Arduino PIC AVR DSP ARM. A wide range of microcontrollers such as Arduino, AVR, PIC, ARM, and so on can control it. The module is triggered, high trigger current less than 5mA, part of the 51 single-chip IO port output capability is weak, pull or increase the drive capability of the circuit. it Can be used for microcontroller development board module or home appliance control.
Specification and Features :Â
- Trigger mode: Low level
- One normally closed contact and one normally open contact
- Pull-down circuit for the avoidance of malfunction
- Triode drive, increasing relay coil
- High impedance controller pin
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control, and load areas isolation trenches.
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
Package included:
1 x 5V 1 channel relay module
SKU: n/a -
Uncategorized
AEROKART INDIA Breadboard Dupont Wire Kit 2pcs 400 Tie-Point 2pcs 830 Tie-Point Solderless Breadboards and 40pin Female to Female Male to Female Male to Male Cable Jumper Wires
-33%UncategorizedAEROKART INDIA Breadboard Dupont Wire Kit 2pcs 400 Tie-Point 2pcs 830 Tie-Point Solderless Breadboards and 40pin Female to Female Male to Female Male to Male Cable Jumper Wires
0 out of 5(0)- High-Quality Solderless Breadboard Dupont Wires Kit
- What You Get: 4pcs 400 & 830 Tie-point Breadboards & 40-pin M/F M/M F/F jumper wires . Perfectly packaged in a box for easy storage and use.
- Widely Application : Breadboards – Perfect for Arduino shield prototyping and testing. Dupont wires kit – Perfectly suitable for any DIY experimental projects.
- Dupont Jumper Wires : 20 cm / 8 inch ; 40pin male to male & 40pin female to male & 40pin female to female multicolored jumper wires; Standard 2.54mm pitch dupont housing connector – headers & sockets.
SKU: n/a -
Uncategorized, Basic Electronic Components, Batteries | Chargers and Accessories, Electronic Components
LI-ION 3.7V 2150MAH WITH Charger Protection Circuit Kit LI-ION
-33%Uncategorized, Basic Electronic Components, Batteries | Chargers and Accessories, Electronic ComponentsLI-ION 3.7V 2150MAH WITH Charger Protection Circuit Kit LI-ION
0 out of 5(0)Lithium-Ion charge protection circuit comes with over-charge, over-discharge, over-current and short circuit protection. MOS transistor can control the battery charge and discharge, Built-in three-stage over-current detection circuit, for a variety of various shapes 3.7 V lithium-Ion batteries.1S 3A BMS is Small size, suitable for many requirements of high integration, low cost. Lithium-Ion Battery for robotic applications. Very lightweight and small size compared to Ni-Cd, Ni-MH and Lead-acid batteries. Very long life without losing charging capacity. In this kit, there is a 1x2200mah rechargeable cell with a 1S 3.7V 3A Battery Protection Circuit. So the user can very easy to make it Battery with Protection Circuit.
Features:
- 1×3.7V 2150mAh Battery
- Low maintenance
- Long life with full capacity for up to 1000 charge cycles
- the high-accuracy voltage detection circuit
- the terminal of the charger using high voltage device
- The built-in three-stage over-current detection circuit
- MOS transistor can control the battery charge and discharge
- Overcharge voltage: 4.25±0.05V
- Overcharge release voltage:4.23±0.05V
- Over-discharge voltage:2.54±0.1V
- Over-current protection: 3A
Bms solder Instructions:
- B+ connected to the battery positive.
- B- take the battery.
- P+ input to the positive battery output
- P- battery negative input output
Package Includes:
1 x Li-Ion 2150mah cell
1 x charger protection circuit
SKU: n/a
There are no reviews yet.