SSOP-48 (0.635 mm pin pitch) to DIP-48 (600 mil body width, 0.1″ pin pitch) surface mount adapter. Topside of board fits surface mount footprint.
-33%
Basic Electronic Components, Electronic Components, PCB Adapter
SSOP-48 to DIP-48 SMT Adapter
SSOP-48 (0.635 mm pin pitch) to DIP-48 (600 mil body width, 0.1″ pin pitch) surface mount adapter. Topside of board fits surface mount footprint. A bottom side of PCB has pads for two single row surface mount vertical headers. This board uses surface mount male vertical headers, which are included.
Package Includes:
1 x SSOP-48 to DIP-48 SMT Adapter.
₹80.00 ₹120.00
Related products
-
Uncategorized, Basic Electronic Components, Batteries | Chargers and Accessories, Electronic Components
LI-ION 3.7V 2150MAH WITH Charger Protection Circuit Kit LI-ION
-33%
Uncategorized, Basic Electronic Components, Batteries | Chargers and Accessories, Electronic ComponentsLI-ION 3.7V 2150MAH WITH Charger Protection Circuit Kit LI-ION
Lithium-Ion charge protection circuit comes with over-charge, over-discharge, over-current and short circuit protection. MOS transistor can control the battery charge and discharge, Built-in three-stage over-current detection circuit, for a variety of various shapes 3.7 V lithium-Ion batteries.1S 3A BMS is Small size, suitable for many requirements of high integration, low cost. Lithium-Ion Battery for robotic applications. Very lightweight and small size compared to Ni-Cd, Ni-MH and Lead-acid batteries. Very long life without losing charging capacity. In this kit, there is a 1x2200mah rechargeable cell with a 1S 3.7V 3A Battery Protection Circuit. So the user can very easy to make it Battery with Protection Circuit.
Features:
- 1×3.7V 2150mAh Battery
- Low maintenance
- Long life with full capacity for up to 1000 charge cycles
- the high-accuracy voltage detection circuit
- the terminal of the charger using high voltage device
- The built-in three-stage over-current detection circuit
- MOS transistor can control the battery charge and discharge
- Overcharge voltage: 4.25±0.05V
- Overcharge release voltage:4.23±0.05V
- Over-discharge voltage:2.54±0.1V
- Over-current protection: 3A
Bms solder Instructions:
- B+ connected to the battery positive.
- B- take the battery.
- P+ input to the positive battery output
- P- battery negative input output
Package Includes:
1 x Li-Ion 2150mah cell
1 x charger protection circuit
SKU: n/a -
Basic Electronic Components, Electronic Components, IoT and Wireless
LoRa Ra-02 SX1278 433MHz Wireless Spread Spectrum Transmission Module
-48%
Basic Electronic Components, Electronic Components, IoT and WirelessLoRa Ra-02 SX1278 433MHz Wireless Spread Spectrum Transmission Module
- Module Model: LoRa-RA-02, Input Supply Range: 2.5 ~ 3.7VDC, Interface: SPI, Programmable bit Rate: UP to 300Kbps
- Antenna Type: IPEX, Frequency Range: 410-525 MHz, Transmit Power: 18±1 dBm (Max), Operating Temperature: -10 to 85°C, LoRa Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change, High sensitivity: down to -148dBm, Half-duplex SPI communication, Programmable bit rates up to 300kbps, Supports FSK, GFSK, MSK, GMSK, LoRa, and OOK modulation modes
- 127dB RSSI dynamic range, Automatic RF signal detection, CAD model, and very high-speed AFC, Packet engine with CRC up to 256 bytes, Small footprint dual-row stamp-hole patch package; Dimension: Length-28mm, Width-20mm, Height-5mm, Weight-7gm
SKU: n/a -
Basic Electronic Components, Electronic Components
MB102 830 Points Solderless Prototype PCB Breadboard
-22%
Basic Electronic Components, Electronic ComponentsMB102 830 Points Solderless Prototype PCB Breadboard
An MB102 830 Points Solderless Prototype PCB Breadboard is an invaluable tool for experimenting with circuit designs whether in the R&D or university lab. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components.
Features :
- Mb102 Bread Board
- 830 Solder-less Points
- Ideal for Experimenting With Circuit Design In Labs
- Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components
- Completely reusable
- Colored coordinates for easy components placement.
- Phosphor bronze nickel plated spring clips.
- Accept a variety of wire sizes 20-29 AWG
SKU: n/a -
Uncategorized, Basic Electronic Components, Electronic Components
Multi-purpose Hot Melt Glue Sticks for Glue Gun – 1 Pcs
-40%
Uncategorized, Basic Electronic Components, Electronic ComponentsMulti-purpose Hot Melt Glue Sticks for Glue Gun – 1 Pcs
Features:
For Almost All Bonding Jobs… Trigger-Feed For Even Glue Flow.
Perfect For Home Repairs Hobbies And Crafts.
How to Use
- Plug-In Gun. Load The Glue Sticks Into The Back Of The Gun.
- Press Trigger Several Times Until The Glue Stick Is Firmly Set Into The Inlet Tube
- Allow The Glue Gun To Warm Up For Approx.5 Minutes (Depend on Glue Gun)
- Squeeze Trigger Until Glue Flows From Nozzle Some Examples Of Usage: Repair Holes In Window Screens Reattach The Float For A Tank After Its Mount Corroded Away Repair Broken Tail Light Covers On Cars Reattach Trim On Cars Reattach
Package Content:
1 x Multi-purpose Hot Melt Glue Sticks for Glue Gun
SKU: n/a
There are no reviews yet.