- Resistance: 1K Ω.
- Tolerance: 5%.
- Surface-mount chip resistor
-16%
Basic Electronic Components, Electronic Components, Resistor, Resistror Reel
1K Ohm 1/8W 805 Resistor(Reel of 5000)
1K Ohm 1/8W 805 Surface Mount Chip Resistor is a small surface-mount resistor. It is a thick film resistor with a ceramic body as a substrate.
₹760.00 ₹900.00
Based on 0 reviews
Be the first to review “1K Ohm 1/8W 805 Resistor(Reel of 5000)”
Related products
-
Basic Electronic Components
RGB 3 Color LED Module For Arduino Red Green Blue
The LED RGB 5 mm Module incorporates a red, green and blue LED with a clear lens in the same 5 mm package with built-in current limiting resistors(150Ω). This is a 3 Color LED Module. Through the PWM adjusting, three primary colors can be mixed to obtain different colors.
Notice that you do not need to use limiting resistors since they are already included on the board.
Features:
- The use of plug-in full-color LED.
- RGB trichromatic limiting resistor to prevent burnout.
- Compatible with Arduino DIY project
- With a variety of single-chip interface.
- Through the PWM adjusting, three primary colors can be mixed to obtain different colors.
Package included:
1xRGB 3 Color LED Module
SKU: n/a -
Basic Electronic Components
7x9cm Prototyping PCB printed circuit experimental board
This is a Universal PCB Prototype Board single-Side 7 X 9 CM High-quality universal prototyping board with standard 0.1″ spacing through holes.
Specification:
Material: Bakelite
Dimension: 7 x 9cm
Thickness: 1.5mm
Hole pitch: 2.54mm
Hole inner diameter: 1.0mmPackage included:
1 X 7x9cm Prototyping PCB printed circuit experimental boardSKU: n/a -
Basic Electronic Components, Electronic Components
BREADBOARD GL-12 840 TIE POINTS SOLDERLESS DIY PROJECT CIRCUIT
-34%
Basic Electronic Components, Electronic ComponentsBREADBOARD GL-12 840 TIE POINTS SOLDERLESS DIY PROJECT CIRCUIT
Description:
- Tie-point 840
- Solderless breadboard (GL-12)
- Wire size: Suitable for 29-20 AWG wires
- Size: About 16.5*5.6*1cm
Package Includes:
1 X GL-12 Breadboard 830 Point Solderless PCB
SKU: n/a -
Basic Electronic Components, Sensors
Eye Blink Sensor Project Kit
The Eye-Blink sensor works by illuminating the eye and eyelid area with infrared light, then monitoring the changes in the reflected light using a phototransistor and differentiator circuit.
This includes Arduino Nano, Eye Blink sensor, Buzzer, Battery, Clip Connector, and Switch.
Eye Blink sensor senses the eyeblink using infrared. The Variation Across the eye will vary as per eye blink. If the eye is closed the output is high otherwise the output is low.
Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality as the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one.
A Standard Active Buzzer Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.
This is a general 9v Battery for all your project and application needs.
A clip Connector is used to connect a 9V battery to the application. This snap power cable to DC 9V clip male line battery adapter for mostly used to power Arduino boards.
Rocker switch is Rocker Switch SPST ON/OFF Microswitch.
SKU: n/a
There are no reviews yet.