- Resolution of 1-mm
- 6Hz read rate
- Internal temperature compensation
- 42kHz ultrasonic sensor measures distance to objects
-6%
Based on 0 reviews
Be the first to review “Maxbotix MB7383 HRXL-MaxSonar WRLST Ultrasonic Sensor”
Related products
-
Sensors
3.5-5.5V Standard Active Buzzer Module For Arduino
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.This module is ideally suited to adding noise to your project and is compatible with a pin pitch of 2.54mm while functioning with microcontrollers such as the Arduino. This module lets you respond to programmatic changes with a lovely annoying buzzer that can be altered over a range of frequencies to ensure maximum irritation. To operate the I/O pin must receive a square wave to trigger the buzzer. This can be produced within all popular microcontrollers.Specification:- Working voltage: 3.5-5.5V
- Working current: <25mA
- PCB Dimension: 1.85 x 1.5 cm (L x W)
Feature:
- An active buzzer with a concussion internal source- so long as it will be called an energized
- The program easy to control- SCM can let a high-low sound- while passive buzzer did not.
- The Transistor drive module uses 8550
- With fixed bolt hole- easy installation- 2.6mm aperture.
Package included:
1 x Standard Active Buzzer ModuleSKU: n/a -
Basic Electronic Components, DIY Learning and Robot Kits, Sensors
L298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
-50%
Basic Electronic Components, DIY Learning and Robot Kits, SensorsL298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
- L298N Motor Driver Controller Module is a high power motor driver for driving DC and Stepper motors. It can control upto 4 DC motors, or 2 DC motors with directional and speed control. This motor driver is for robotics and mechatronics projects. The 150 RPM Dual Shaft BO Motor is a straight motor which gives good torque and RPM at lower operating voltages. It is a geared DC Motor. It is an alternative to metal gear DC motors. The 65MM Wheel is made up of standard grade rubber.
- L298N: Current Sense for each motor | Heatsink for better performance | Power-On LED indicator | Directional control | Speed control | High power motor || BO motor: Low density and inertia | Capability to absorb shock and vibration as a result of elastic compliance | Ability to operate with minimum or no lubrication | Relatively low coefficient of friction || Wheel: Car hub is reinforced nylon | Sturdy | Tire with sponge liner for more strength | With upgraded tire tread for greater friction
- Dimensions: L298N(LxWxH):44x44x28mm | Shaft length:7mm | Shaft Diameter:5.5mm | Motor(LxWxH):55x48x23mm | Diameter of wheel:65mm | Center Shaft Hole Diameter (mm):5.4 (Round edge) and 3.5 (Flat edge)
- The L298N motor driver is perfect for robotics and mechatronics projects. It can also be used for controlling motors from microcontrollers, switches, relays, etc. It is capable of driving DC and Stepper motors for micro mouse, line following robots, robot arms, etc. The BO motor is ideal for DIY enthusiasts. This motor set is inexpensive, small, easy to install and ideally suited for use in a mobile robot car. The 65mm wheel is only compatible with BO motor.
- L298N: Input Voltage:3.2V-40V DC | L298N Dual H-Bridge DC Motor Driver | Operating voltage:DC 5V-35V | Peak Current:2Amps | Speed Control:PWM | Control Signal input voltage range:0.3V≤Vin≤1.5V (Low), 2.3≤Vin≤Vss (High) | Max. power consumption:20W (when the temperature T=75℃) || BO Motor: Operating Voltage:3 to 12V | Current (without loading):40-180mA | RPM:100 | Output Torque:0.8 kgcm | Motor Design: L-shaped || Wheel: Loading Capacity (kg):2.5 | D hole For BO Motor (mm):6
SKU: n/a -
DIY Learning and Robot Kits, Sensors
Arduino Sensors Combo of 5 Kit
This is a basic combo for Arduino and Robotics starter. This set can be used for obstacle sensing cars, Ultrasonic radars, school projects i.e. automatic barrier, automatic light, etc. This combo includes an ultrasonic sensor, motion sensor, IR obstacle sensor, LDR, SG90 Servo motor.
HC-SR04-Ultrasonic Distance Measuring Sensor is a very popular sensor that is found in many applications where it requires measuring distance and detect objects.
HC-SR501 PIR Motion Detector Sensor Module is a pyroelectric device that detects motion by measuring changes in the infrared levels emitted by surrounding objects. This motion can be detected by checking for a high signal on a single I/O pin.
IR sensor module is adaptable to the environment, with a working voltage of 3.3 V to 5 V. It has a pair of infrared transmitting and receiving tubes when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube.
Photoresistor also is known as LDR(Light Dependent Resistor) as the names imply, changes the resistance with the variation in the amount of light. This particular photoresistor has a resistance of 5-10k Ohm in light and about 500k Ohm resistance in the dark.
Micro Servo 9GÂ is lightweight, high-quality, and lightning-fast. The servo is designed to work with almost all radio control systems. It is with excellent performance that brings you to another horizon of flight. The SG90 mini servo with accessories is perfect for R/C helicopter, plane, car, boat, and truck use.
SKU: n/a -
Sensors
RC522 RFID 13.56MHZ Reader Writer Module
RC522 – RFID Reader /Writer with Cards Kit includes a 13.56MHz RF reader and writer module that uses an RC522 IC and two S50 RFID cards tag. The MF RC522 is an integrated transmission module for contactless communication at 13.56 MHz. RC522 supports ISO 14443A/MIFARE mode. RC522 – RFID Reader features an outstanding modulation and demodulation algorithm to serve effortless RF communication at 13.56 MHz. The S50 RFID Cards will ease up the process helping you to learn and add the 13.56 MHz RF transition to your project.
The module uses SPI to communicate with microcontrollers. The open-hardware community already has a lot of projects exploiting the RC522 – RFID Communication, using Arduino.
Features:-
- The low-voltage, low-cost, small size of the non-contact card chip to read and write.
- 13.56MHz contactless communication card chip.
- MFRC522 supports the MIFARE series of high-speed non-contact communication, two-way data transmission rate up to 424kbit/s.
- ISO14443A frames and error detection.
- Suitable for Smart meters and portable handheld devices.
- Advanced modulation and demodulation concept completely integrated with all types of 13.56MHz passive contactless communication methods and protocols.
- 14443A compatible transponder signals.
- Supports rapid CRYPTO1 encryption algorithm, terminology validation MIFARE products.
- The reader and RF card terminal design meet advanced application development and production needs.
- Can be directly loaded into the various reader molds, very convenient.
Specifications:-
- Operating Frequency: 13.56MHz
- Reader Distance: ≥ 50mm / 1.95″ (mifare 1)
- Operating Current :13-26mA / DC 3.3V
- Idle Current :10-13mA / DC 3.3V
- Peak Current: < 30mA
- Sleep Current: < 80uA
- Data transfer rate: Maximum 10Mbit/s
- Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, mifare Pro, MIFARE DESFire
- Environmental Storage Temperature: -40 – 85 degrees Celsius
- Environmental Operating Temperature: -20 – 80 degrees Celsius
- Relative humidity: 5% – 95%
- Module interface: SPI
SKU: n/a
There are no reviews yet.