- Working voltage range: DC 5-18 V
- Flow range : 10-200 Liter per min
- Maximum current : 15 mA (5 volt DC)
- Operating Temp : up to 80C,Operating humidity:35%-90%RH
- Allow compression : Water pressure 1.75 Mpa below
- Insulation resistance : >100M OHM
- Storage Temperature : -25-80C
- Storage humidity : 25%-95%RH
-17%
Sensors
Water Flow Sensor (Sea) YFDN50 Flowmeter G2 10- 200L/min 5-24V
- Working voltage range: DC 5-18 V
- Flow range : 10-200 Liter per min
- Maximum current : 15 mA (5 volt DC)
- Operating Temp : up to 80C,Operating humidity:35%-90%RH
- Allow compression : Water pressure 1.75 Mpa below
- Insulation resistance : >100M OHM
- Storage Temperature : -25-80C
- Storage humidity : 25%-95%RH
₹4,782.00 ₹5,782.00
Based on 0 reviews
Be the first to review “Water Flow Sensor (Sea) YFDN50 Flowmeter G2 10- 200L/min 5-24V”
Related products
-
Sensors
37 in 1 Sensors Kit compatible with Arduino
- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
- Infrared sensor receiving module
- Laser sensor module
- Temperature and humidity sensor module
- Infrared sensor module
- 5v relay module
- Obstacle avoidance sensor module.
SKU: n/a -
Basic Electronic Components, Sensors
Eye Blink Sensor Project Kit
The Eye-Blink sensor works by illuminating the eye and eyelid area with infrared light, then monitoring the changes in the reflected light using a phototransistor and differentiator circuit.
This includes Arduino Nano, Eye Blink sensor, Buzzer, Battery, Clip Connector, and Switch.
Eye Blink sensor senses the eyeblink using infrared. The Variation Across the eye will vary as per eye blink. If the eye is closed the output is high otherwise the output is low.
Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality as the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one.
A Standard Active Buzzer Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.
This is a general 9v Battery for all your project and application needs.
A clip Connector is used to connect a 9V battery to the application. This snap power cable to DC 9V clip male line battery adapter for mostly used to power Arduino boards.
Rocker switch is Rocker Switch SPST ON/OFF Microswitch.
SKU: n/a -
Sensors
PIR Motion Detector Sensor Module
The HC-SR501 PIR Motion Detector Sensor Module is a pyroelectric device that detects motion by measuring changes in the infrared levels emitted by surrounding objects. This motion can be detected by checking for a high signal on a single I/O pin.
The module has an onboard pyroelectric sensor, conditioning circuitry, and a dome-shaped Fresnel lens. It has a delay time adjustment Potentiometer and sensitivity adjustment Potentiometer.
It is used to sense the movement of people, animals, or other objects. They are commonly used in burglar alarms and automatically-activated lighting systems. Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc.
Features:
- Compact size
- Infrared sensor: dual-element, low noise, high sensitivity
- Blockade time: 2.5s (Default)
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
SKU: n/a
There are no reviews yet.