Recommended Products
Raspberry Pi 4 Model-B with 8 GB RAM
Shop
Showing 1513–1536 of 6090 results
-
Basic Electronic Components
AT24C256 I2C Interface EEPROM Memory Module
AT24C256 I2C Interface EEPROM Memory Module
If you need to do some data storage in Arduino, then using the EEPROM is probably the most simple practices. In actual, Arduino used the ATmega chip itself has a certain EEPROM memory, but only a limited number. Here is the external EEPROM memory module which uses the I2C bus line to connect with Arduino, and with a pluggable chip, insert in this series, so it will easy to expand capacity, basically just need to insert a bigger capacity of EEPROM chip.
The AT24C256 I2C Interface EEPROM Memory Module is based on EEPROM chips of FT24C256A series, 256K bit capacity, that’s 32k bytes. The EEPROM module communicates with Arduino through the I2C interface. It will be better to use with Arduino-Sensor-Shield-V4.0 and the Arduino-I2C-COM-Cable.162
SKU: n/a -
-
Basic Electronic Components, Electronic Components, Wire Wound Inductors
ATCA-01-101M-V Toroidal Inductor
-19%
Basic Electronic Components, Electronic Components, Wire Wound InductorsATCA-01-101M-V Toroidal Inductor
Toroidal Inductor, Low EMI, ATCA, 100 µH, 2 A, 0.081 ohm, ± 20%
Note:
- For more technical details, go through the datasheet in the attachments
- Image may vary from actual product in terms of brand and value printed
SKU: n/a -
Basic Electronic Components
ATmega328P 5V Nano V3.0 Development Board 16MHz CH340 Type-C
Product Description
This Arduino-compatible Nano V3.0 micro-controller is a small, complete, micro-controller board based on the ATmega328 MCU. It has more or less the same functionality as the Arduino Duemilanove, but in a smaller package. It lacks only a DC power jack, and uses the more compact Mini USB (Mini-B) connector instead of a standard USB connector. It is compatible with Arduino programs and the Arduino IDE. This version of the Nano uses the CH340G USB interface controller. It can be powered via the Mini-B USB connection, a 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
CH340 is a USB bus conversion chip, it can realize USB to UART interface or USB to printer interface. In serial UART mode, CH340 provides common MODEM liaison signal, used to expand UART interface of computer or upgrade the common serial device to USB bus directly.SKU: n/a -
Basic Electronic Components
ATMEGA8515-16PU MICROCHIP
The ATMEGA8515 is a high-performance, low-power microcontroller based on the Atmel 8-bit AVR RISC architecture. It features 8KB of programmable flash memory, 544B of internal SRAM, and supports up to 64KB of external SRAM, along with 512B of EEPROM. Operating within a voltage range of 2.7 to 5.5 volts, it delivers a throughput of 16 MIPS at 16MHz.
With its single-cycle instruction execution, the ATMEGA8515 achieves a throughput of nearly 1 MIPS per MHz, offering an optimal balance of processing power and energy efficiency.
SKU: n/a -
Development Boards
ATmel MCU ATMEGA16U2 MEGA 2560 R3 Improved Version CH340G Board
- Microcontroller CH340
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- Dimensions : 111 x 54 x 12 (LxWxH) mm.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Automatic Aquarium Adjustable Fish Feeding 1/2 Times Daily Food Dispenser Fish Feeder
-34%
Motors | Drivers | Pumps | ActuatorsAutomatic Aquarium Adjustable Fish Feeding 1/2 Times Daily Food Dispenser Fish Feeder
- New and high quality and Easy to install on edge of fish Pot.
- Dry, loose flake and pellet food can be used
- Ideal for various sizes of aquariums with two options of placing the food feeder on aquarium,
- Free-standing or rim-mounted
- Digital timer for setting up regular feeding programs
SKU: n/a -
Uncategorized
Automatic three phase Changer Over
The Automatic Three-phase Changer Over feature is now the need of the day. It is user-friendly and easy to use. It saves time too. This project is also a prototype for the automation of the system. In the earlier days (even today at some places) the manual operations are frequent. When the main supply goes off the person manually turns on the generator. In the case of the electrical appliance control using automation causes more safety.
The Phase change-over can only be installed with a three-phase supply. The selection of Phase change over is done according to the mains load. This kit automatically gives an output of all the three-phase either one or two phases are missing, and after the return or presence of all three-phase, it diverts automatically to its originating phase.
This Automatic three-phase Changer Over kit is a prototype for the same which is auto change over to generator when the main supply fails. In this system, we are designing an embedded circuit to control this. In case there are two phases, then the switching will be in the default phase. Three relays are there to control the switching.
Automatic three-phase Changer Over is a prototype for the same which is auto change over to generator when the main supply fails.
It is user-friendly and easy to use.
Automatic three-phase Changer Over kit is also a prototype for the automation of the system.Physical Attributes
Dimensions (cm) L x W x H : 28 x 24 x 8
Weight (gm): 1000SKU: n/a -
ARM Microcontroller
AVNET Development Kit, 96Boards Click Mezzanine Starter Kit, LS Mezzanine Board, 3 x Click Boards
-11%
ARM MicrocontrollerAVNET Development Kit, 96Boards Click Mezzanine Starter Kit, LS Mezzanine Board, 3 x Click Boards
- Product: AVNET Development Kit, 96Boards Click Mezzanine Starter Kit, LS Mezzanine Board, 3 x Click Boards
- LS Mezzanine connectivity
- Two MikroBUS sites, with the following interfaces –UART,SPI,I2C,PWM,Analog input,On-board ADC
- Additionally, the SK also includes three Click boards
- 6 Degree-of-Freedom Inertial Measurement
- 2×16 Character Display –USB-UART
SKU: n/a -
Drone Accessories
Axl Orbit M10 GPS
Item Type: GPS No. of Concurrent GNSS Up to 4 GNSS – BeiDou – Galileo – GLONASS – GPS Frequency Band – GPS L1 – Galileo E1 – GLONASS L1 – BeiDou B1 Nav. update rate(Hz) Up to 5 Hz (4 concurrent GNSS) GNSS Augmentation System EGNOS, GAGAN, MSAS and WAAS  Inp
ut Voltage (V)
4.7-5.2V Power Consumption (mA) Less than 200mA @ 5V Operating Temperature (°C) -40~80C Dimensions (L x W x H) mm – ∅47.36×10.05mm (w/o Case) – ∅52.4×17.8mm (With Case) Weight (g): – 41.05g (w/o Case) – 51.21g (With Case) SKU: n/a -
Basic Electronic Components
B Type Aluminium Heat Sink for MK7 MK8 Extruder
A type-B aluminium heat sink that fits the extruder part of a 3D printer. It is compatible with the MK7 and MK8 models of 3D printer extruders.
Feature:
1. Aluminum material, heat quickly.
2. Chip spacing and neat, larger heat dissipation area.
3. Surface oxidation treatment, heat fast, high hardness, beautiful colourSKU: n/a
