Recommended Products
Raspberry Pi
Raspberry Pi 4 Model-B with 8 GB RAM
Quad-Core 64-bit Broadcom 2711, Cortex A72Â Processor
WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz)
LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0)
Operating Power 5V@3A via USB Type-C port
Dual-Display Micro HDMI Ports which supports H 265 Decode for 4K Video @60p
SKU: n/a
Shop
Showing 1801–1824 of 6090 results
-
Motors | Drivers | Pumps | Actuators
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
SKU: n/a -
Development Boards
Cytron 40 pins PIC Start-Up Kit SK40C
-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
Operating Voltage Range: 7V – 15VDC
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
SKU: n/a -
-
Development Boards
Cytron Arduino PS2 Shield
- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron Dual channel 10A Motor Driver UNO Robot Controller
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
-31%
Motors | Drivers | Pumps | ActuatorsCytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from  5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Development Boards
Cytron ESP8266 WiFi Shield V2.0 W/ Micro SD Card Slot For Arduino Uno
- Basically, Rev2.0 utilize WROOM-02 instead of ESP8266-12 as the WiFi module.
- Separate 3.3V voltage regulator for ESP8266-12 WROOM-02 module, 500mA max output.
- Each and every board is preassembled and tested before it is being shipped out to you.
- 802.11 b/g/n.
- Support Wi-Fi Direct (P2P), soft-AP.
- Integrated TCP/IP protocol stack.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron FD04A 4-Channel Motor Driver
- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: n/a -
Development Boards
Cytron LCD keypad Shield High Quality
- Provides a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron Maker Drive H-Bridge Motor Driver
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA)Â to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
SKU: n/a -
Sensors
Cytron Maker Line: Simplifying Line Sensor For Beginner
- Operating Voltage: DCÂ 3.3V and 5V compatible (With reverse polarity protection).
- Recommended Line Width: 13mm to 30mm.
- Sensor Refresh Rate: 200Hz
- Easy calibration process.
- Supports a wide range of controllers such as Arduino, Raspberry Pi, etc.
SKU: n/a -
Sensors
Cytron Maker Reflect: Simplifying IR Reflectance Sensor for Beginner
- Operating Voltage: 3.3V and 5V Compatible
- Sensing Distance (Height): 1mm to 40mm (Vcc = 5V, Blackline on a white surface)
- Features a tiny reflectance sensor
- This sensor is used in line following robot
- Fits easily in the tightest space
SKU: n/a -
Development Boards
Cytron Maker UNO Microcontroller Board- Arduino UNO Compatible Module
- SMD ATmega328P microcontroller(the same microcontroller on Arduino UNO) with Optiboot (UNO) Bootloader
- USB Programming facilitated by the CH340
- Input voltage: USB 5V, from computer, power bank or standard USB adapter
- Piezo buzzer that will act as simple audio output
- 500mA (maximum) 3.3V voltage regulator
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP 6-pin Header
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
-25%
Motors | Drivers | Pumps | ActuatorsCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
-28%
Motors | Drivers | Pumps | ActuatorsCytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: n/a -
Motors | Drivers | Pumps | Actuators
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
Motors | Drivers | Pumps | Actuators
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
SKU: n/a -
-
Development Boards
Cytron Uno Board ATmega328 Microcontroller (Arduino Compatible)
- A better version of Arduino Uno
- SMD ATmega328 microcontroller with Optiboot (UNO) Bootloader
- USB Programming Facilitated by the Ubiquitous FTDI FT231X (more stable)
- Input voltage: DC7-15V
- 14 Digital I/O Pins (6 PWM outputs)
SKU: n/a -
Development Boards
Cytron XBee Shield
-
Mounts directly onto your Arduino
-
DIN and DOUT pins of XBee can be connected to either the USB’s UART pins or another digital pin on the Arduino (D0, D1, D2, D3, D8, D9, D10, D11)
-
3.3V power regulation and proper level shifting on-board communication between 5V and 3.3V
-
Extra 0.1″ spaced prototyping holes
-
Reset button brought out to shield
-
Power, DIN, DOUT, RSSI, and DIO5 indicator LEDs
SKU: n/a -
