- Model: DFRobot Gravity Analog CO2 Gas Sensor
- Heating Voltage: 6.0±0.1 V
- Heating Resistor: 30.0±5%Ω
- Heating Current: at 200mA
- Heating Power: 1200mW
-14%
Based on 0 reviews
Be the first to review “DFRobot Gravity Analog CO2 Gas Sensor For Arduino (MG-811 Sensor)”
Related products
-
Sensors
HC-05 Bluetooth Wireless UART Module
HC-05 is a Bluetooth Transceiver Module and has TTL Output. HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. This Bluetooth module is a completely qualified Bluetooth V2+Enhanced Data Rate (EDR). It is 3Mbps Module with 2.4GHz radio transceiver and baseband. It has CSR Bluecore 04, an external single-chip Bluetooth system with CMOS technology and AFH, Adaptive Frequency Hopping, feature.
The HC-06 module is a slave only device. This means that it can connect to most phones and computers with Bluetooth but it cannot connect to another slave-only device such as keyboards and other HC-06 modules. To connect with other slave devices a master module would be necessary such as the HC-05 version which can do both master and slave.
Specification and Features:
- Voltage supply: 3.5v to 5v
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- With the integrated antenna and edge connector
- Sensitively: -80dBm
- RF Transmit Power: up to +4dBm
- Supported baud rate: 9600, 19200, 38400, 57600, 115200, 230400 and 460800
- Slave default baud rate: 9600
- Data bits: 8
- Stop bit: 1
- Parity: no parity
- A programmable input-output control
- Supported device: laptop, desktop, mobile, tablet
- Protocol: IEEE802.15.1
- Dormancy current: no dormancy.
- Bluetooth module HC-05 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Security: Authentication and encryption.
SKU: n/a -
Sensors
3.5-5.5V Standard Active Buzzer Module For Arduino
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.An active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include alarm devices, timers, and confirmation of user input such as a mouse click or keystroke.This module is ideally suited to adding noise to your project and is compatible with a pin pitch of 2.54mm while functioning with microcontrollers such as the Arduino. This module lets you respond to programmatic changes with a lovely annoying buzzer that can be altered over a range of frequencies to ensure maximum irritation. To operate the I/O pin must receive a square wave to trigger the buzzer. This can be produced within all popular microcontrollers.Specification:- Working voltage: 3.5-5.5V
- Working current: <25mA
- PCB Dimension: 1.85 x 1.5 cm (L x W)
Feature:
- An active buzzer with a concussion internal source- so long as it will be called an energized
- The program easy to control- SCM can let a high-low sound- while passive buzzer did not.
- The Transistor drive module uses 8550
- With fixed bolt hole- easy installation- 2.6mm aperture.
Package included:
1 x Standard Active Buzzer ModuleSKU: n/a -
Sensors
iR Avoidance Proximity Sensor E18-D80NK For 5V Switch Detect 3-80cm For Robotics
- Model: E18-D80NK
- This is a set of transmitter and receiver in one of the photoelectric sensor
- A detection distance can be adjusted according to the requirements
- The production line of automatic counting equipment goods
- Diameter: 17MM
SKU: n/a
There are no reviews yet.