- Voltage Sensitivity (open-circuit, baseline): 1.1 V/g.
- Charge Sensitivity (baseline): 260 pC/g.
- Resonance Frequency: 75 Hz.
- Voltage Sensitivity (open-circuit, at resonance): 6 V/g.
- Upper Limiting Frequency (+3 dB): 42 Hz.
Related products
-
Sensors
HC-05 Bluetooth Wireless UART Module
0 out of 5(0)HC-05 is a Bluetooth Transceiver Module and has TTL Output. HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. This Bluetooth module is a completely qualified Bluetooth V2+Enhanced Data Rate (EDR). It is 3Mbps Module with 2.4GHz radio transceiver and baseband. It has CSR Bluecore 04, an external single-chip Bluetooth system with CMOS technology and AFH, Adaptive Frequency Hopping, feature.
The HC-06 module is a slave only device. This means that it can connect to most phones and computers with Bluetooth but it cannot connect to another slave-only device such as keyboards and other HC-06 modules. To connect with other slave devices a master module would be necessary such as the HC-05 version which can do both master and slave.
Specification and Features:
- Voltage supply: 3.5v to 5v
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- With the integrated antenna and edge connector
- Sensitively: -80dBm
- RF Transmit Power: up to +4dBm
- Supported baud rate: 9600, 19200, 38400, 57600, 115200, 230400 and 460800
- Slave default baud rate: 9600
- Data bits: 8
- Stop bit: 1
- Parity: no parity
- A programmable input-output control
- Supported device: laptop, desktop, mobile, tablet
- Protocol: IEEE802.15.1
- Dormancy current: no dormancy.
- Bluetooth module HC-05 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Security: Authentication and encryption.
SKU: n/a -
Sensors
PIR Motion Detector Sensor Module
0 out of 5(0)The HC-SR501 PIR Motion Detector Sensor Module is a pyroelectric device that detects motion by measuring changes in the infrared levels emitted by surrounding objects. This motion can be detected by checking for a high signal on a single I/O pin.
The module has an onboard pyroelectric sensor, conditioning circuitry, and a dome-shaped Fresnel lens. It has a delay time adjustment Potentiometer and sensitivity adjustment Potentiometer.
It is used to sense the movement of people, animals, or other objects. They are commonly used in burglar alarms and automatically-activated lighting systems. Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc.
Features:
- Compact size
- Infrared sensor: dual-element, low noise, high sensitivity
- Blockade time: 2.5s (Default)
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
SKU: n/a -
Basic Electronic Components, DIY Learning and Robot Kits, Sensors
L298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
-50%Basic Electronic Components, DIY Learning and Robot Kits, SensorsL298N 2A Based Motor Driver Controller Module+100RPM Dual Shaft BO Motor (4pcs)+4 x 65mm Robot Wheel-Combo
0 out of 5(0)- L298N Motor Driver Controller Module is a high power motor driver for driving DC and Stepper motors. It can control upto 4 DC motors, or 2 DC motors with directional and speed control. This motor driver is for robotics and mechatronics projects. The 150 RPM Dual Shaft BO Motor is a straight motor which gives good torque and RPM at lower operating voltages. It is a geared DC Motor. It is an alternative to metal gear DC motors. The 65MM Wheel is made up of standard grade rubber.
- L298N: Current Sense for each motor | Heatsink for better performance | Power-On LED indicator | Directional control | Speed control | High power motor || BO motor: Low density and inertia | Capability to absorb shock and vibration as a result of elastic compliance | Ability to operate with minimum or no lubrication | Relatively low coefficient of friction || Wheel: Car hub is reinforced nylon | Sturdy | Tire with sponge liner for more strength | With upgraded tire tread for greater friction
- Dimensions: L298N(LxWxH):44x44x28mm | Shaft length:7mm | Shaft Diameter:5.5mm | Motor(LxWxH):55x48x23mm | Diameter of wheel:65mm | Center Shaft Hole Diameter (mm):5.4 (Round edge) and 3.5 (Flat edge)
- The L298N motor driver is perfect for robotics and mechatronics projects. It can also be used for controlling motors from microcontrollers, switches, relays, etc. It is capable of driving DC and Stepper motors for micro mouse, line following robots, robot arms, etc. The BO motor is ideal for DIY enthusiasts. This motor set is inexpensive, small, easy to install and ideally suited for use in a mobile robot car. The 65mm wheel is only compatible with BO motor.
- L298N: Input Voltage:3.2V-40V DC | L298N Dual H-Bridge DC Motor Driver | Operating voltage:DC 5V-35V | Peak Current:2Amps | Speed Control:PWM | Control Signal input voltage range:0.3V≤Vin≤1.5V (Low), 2.3≤Vin≤Vss (High) | Max. power consumption:20W (when the temperature T=75℃) || BO Motor: Operating Voltage:3 to 12V | Current (without loading):40-180mA | RPM:100 | Output Torque:0.8 kgcm | Motor Design: L-shaped || Wheel: Loading Capacity (kg):2.5 | D hole For BO Motor (mm):6
SKU: n/a
Reviews
There are no reviews yet