Recommended Products
Raspberry Pi 4 Model-B with 8 GB RAM
Shop
Showing 4873–4896 of 6090 results
-
-
-
Basic Electronic Components, Electronic Components, IoT and Wireless, Uncategorized
RF434 Transmitter Receiver Wireless Module
-58%
Basic Electronic Components, Electronic Components, IoT and Wireless, UncategorizedRF434 Transmitter Receiver Wireless Module
- Range in Open Space(m) : 30m
- Transmitter Frequency Range(MHz) : 433.92
- Receiver Frequency Range(MHz): 433
- Sensitivity :105 dBm
- This hybrid 433Mhz RSI Wireless Transmitter Receiver Module provides a complete RF transmitter and receiver module solution which can be used to transmit data at up to 3KHz from any standard CMOS/TTL source
SKU: n/a -
Sensors
RFID 13.56MHz Card-5Pcs
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Anticollision
- Typical ticketing transaction: <100 ms ( including backup management)
SKU: n/a -
Sensors
RFID Reader/Writer RC522 SPI S50 with RFID Card and Tag
- Voltage:Â DC 3.3V (Do not use 5V supply)
- Operating Current :13-26mA
- Idle Current :10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Typical operating distance in reading/Write mode up to 50 mm
SKU: n/a -
IoT and Wireless, IR and RF Transmitter and Receivers
RFM69HCW Wireless Receiving Module-434 MHz
-10%
IoT and Wireless, IR and RF Transmitter and ReceiversRFM69HCW Wireless Receiving Module-434 MHz
RFM69 series wireless communication module is designed to work at 434Mhz ISM band global free application. It is designed for low-power, high-bandwidth wireless digital communications module. The modules have a low cost, small, stable, product consistency and other characteristics
SKU: n/a -
Basic Electronic Components
RGB 3 Color LED Module For Arduino Red Green Blue
The LED RGB 5 mm Module incorporates a red, green and blue LED with a clear lens in the same 5 mm package with built-in current limiting resistors(150Ω). This is a 3 Color LED Module. Through the PWM adjusting, three primary colors can be mixed to obtain different colors.
Notice that you do not need to use limiting resistors since they are already included on the board.
Features:
- The use of plug-in full-color LED.
- RGB trichromatic limiting resistor to prevent burnout.
- Compatible with Arduino DIY project
- With a variety of single-chip interface.
- Through the PWM adjusting, three primary colors can be mixed to obtain different colors.
Package included:
1xRGB 3 Color LED Module
SKU: n/a -
-
Basic Electronic Components
Right Side MK8 extruder Aluminum 3D Printer Block
Right Side MK8 extruder Aluminum 3D Printer Block
This product is an MK8 Extruder Replacement Aluminum Alloy Block. It can be used to replace an extruder that is blocked or damaged. The product comes as a kit that the user needs to assemble. There are many assembly instructions and videos online that can help with this process.
The MK8 Extruder has three different types: Right Side, Left Side and Right Short. These types indicate the direction of the filament extrusion relative to the block. For single extruders, any type is suitable. For dual extruders, one right side and one left side are needed.
Specifications and Features:
- Right Short Side MK8 Extruder
- High-Quality Replacement for your blocked/damaged MK8 Extruder
- Available in 3 different types to support dual extruder setup.
- Material: Aluminum alloy
- Weight: 60gm
SKU: n/a -
Basic Electronic Components
Right Side MK8 extruder Aluminum 3D Printer Block
Right Side MK8 extruder Aluminum 3D Printer Block
This product is an MK8 Extruder Replacement Aluminum Alloy Block. It can be used to replace an extruder that is blocked or damaged. The product comes as a kit that the user needs to assemble. There are many assembly instructions and videos online that can help with this process.
The MK8 Extruder has three different types: Right Side, Left Side and Right Short. These types indicate the direction of the filament extrusion relative to the block. For single extruders, any type is suitable. For dual extruders, one right side and one left side are needed.
Specifications and Features:
- Right Short Side MK8 Extruder
- High-Quality Replacement for your blocked/damaged MK8 Extruder
- Available in 3 different types to support dual extruder setup.
- Material: Aluminum alloy
SKU: n/a
